Couple lift questions from great Mud minds

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jan 25, 2008
Threads
172
Messages
1,666
Location
Opelika, AL
I have a 94 sitting stock on 35's at the moment. What I have collected over the past few months is a pieced together lift.
Okay so this is what I have so far and am getting.

Have:
Ome 2.5" Heavy front
Ome 2.5" Medium rear
1 3/8" spacer --- which can be shaved if need be
FOR bumpstops and swaybar extentions
FOR revalved Bilstein shocks
Slee +4 brake lines
Acquiring:
Landtanks CC plates

At the moment I have 2* OME bushings and 3* FOR bushings which I'm selling in favor of Landtanks plates. I've already taken my front bumper off and will be taking some of my rear off tomorrow. I'm going to put a front tube bumper and winch on in the future and unsure about the rear. Point is I'm trying to stay as light as possible. So here comes the questions.

1). I don't want to move up to a DC driveshaft so where do I need to keep my lift so I don't have to do that? I can shave the front spacers if needed.
2). I have talked to Landtank a little through PM but was wondering where I need to be lift wise to use his plates?
3). Can I have my cake and eat it too? Enough lift to warrant Landtank's plates but not enough to warrant a DC driveshaft.
 
Why don't you want the DC, just cost? It's a no brainer to use the CC plates to set pinion angle for a DC (do a Tacoma shaft). It may be tough to pick your caster change with the stock shaft because you won't have a defined point for rotation.

If you go to far, you may have vibes and also not be aligned for the DC shaft depending on your lift height.
 
Why don't you want the DC, just cost? It's a no brainer to use the CC plates to set pinion angle for a DC (do a Tacoma shaft). It may be tough to pick your caster change with the stock shaft because you won't have a defined point for rotation.

If you go to far, you may have vibes and also not be aligned for the DC shaft depending on your lift height.

Yeah the cost. I'm kinda lost after you say "Tacoma shaft."
 
Yeah the cost. I'm kinda lost after you say "Tacoma shaft."

With a DC shaft, you simply set the LT CC plates to align the shaft at a zero degree u-joint angle on the axle end.

With the stock shaft, how much are you going to rotate it? Because that will define your likelihood of vibes with the stock shaft.
 
With a DC shaft, you simply set the LT CC plates to align the shaft at a zero degree u-joint angle on the axle end.

With the stock shaft, how much are you going to rotate it? Because that will define your likelihood of vibes with the stock shaft.

Ummmm...., I'm going to put landtanks plates on with clamps and drill through the predrilled pilot hole I thought. Are you saying I have to figure out where to drill the hole? I haven't done my homework on researching these plates since I just decided to go this route. Does LT's plates not turn the pinion up slightly to decrease the angle between the Tcase and front diff?
 
What Nay is posting would be the procedure for setting up the axle for ideal pinion angle. However there are tolerances when doing this and every person who has used my plates has set them up the same without issues that couldn't be resolved by using a DC shaft if need be.

I'm happy to work with anyone who wants to take the extra step to verify that my stock drilling position is correct for their truck.
 
CJ, I have the same springs you do (and year LC). The longer you are here, and the more you read, you will realize that 2 people can do the same things and get different results. A lot of the issues that pop up could be solely lift related, but some if not many have been traced back to other things going on.

In the end, Kudos for taking the time to assemble a your own kit. I was nervous about diving in and creating problems where none existed before (I don't, or haven't yet I should say, wheeled enough to even justify lifting my truck).

I dropped in the full OME kit, no bump stops or extension, run on 33's, and had the OME's pressed in. I had a pm to Landtank (still do) if I ran into any issues. None so far.

All I'm saying is lifting a truck can get you into more money than leaving it alone. Just be prepared if you do it, you might have to spend more to get it right. That might eat into other mod's funds, but just accept it or punt.

There are no black and white answers that apply to every situation and truck. Too many other variables.

Just do it, or don't.
 
Back
Top Bottom