CLOSED. Weathertech/Husky Decal Replacement Decals w Land Cruiser Logo--I have a few sets of Husky decals still available. FCFS! (1 Viewer)

Status
Not open for further replies.
Joined
Nov 2, 2006
Messages
1,436
Location
Spokane
The Husky's turned out ok. Measurement length was off a tad.

20190930_185802.jpg


20190930_185935.jpg


20190930_185808.jpg
 
Joined
Nov 2, 2006
Messages
1,436
Location
Spokane
Looks good...going to refine for better measurement or going with this?

I'll get it refined. Corner radius needs adjustment too. I worry that since I only have others measurements, the weathertech may not be perfect. I may need someone to pull a sticker out for accurate placement.
 
Joined
Nov 2, 2006
Messages
1,436
Location
Spokane
I have 3 of the above for husky
Let me know if you need more or different measurements on the weathertechs.

It would be helpful to have exact measurements with the sticker removed. I also need the corner radius to ensure the edge lines up correctly.
 
Joined
Nov 2, 2006
Messages
1,436
Location
Spokane
I have one set of three available for the Husky's as shown above. $15 shipped.
 
Joined
Nov 4, 2005
Messages
136
Location
Maine
I found the front drivers sticker that fell off my weathertec’s. It’s 30mm x 117mm. Slightly shorter than previous posters (119 I believe?) Mines an 08, purchased the mat’s in 2012. I could always trim it to fit.
 
Joined
Nov 2, 2006
Messages
1,436
Location
Spokane
I found the front drivers sticker that fell off my weathertec’s. It’s 30mm x 117mm. Slightly shorter than previous posters (119 I believe?) Mines an 08, purchased the mat’s in 2012. I could always trim it to fit.

My understanding is the mats from 08-current are the same. I just want to make sure I get the right measurements so everyone gets a good sticker. I'm actually fine with the samples that I put in my rig and will keep them. They are a bit tight top to bottom, but they appear to be staying in without additional adhesive.

I'm going to start an order for Husky labels as I should have the size down now. I'm going to wait on the Weathertech until I can lock down a measurement. Getting the corner radius will be imperative to a perfect fit (which I am learning from the samples I received).
 
Joined
Nov 4, 2005
Messages
136
Location
Maine
My understanding is the mats from 08-current are the same. I just want to make sure I get the right measurements so everyone gets a good sticker. I'm actually fine with the samples that I put in my rig and will keep them. They are a bit tight top to bottom, but they appear to be staying in without additional adhesive.

I'm going to start an order for Husky labels as I should have the size down now. I'm going to wait on the Weathertech until I can lock down a measurement. Getting the corner radius will be imperative to a perfect fit (which I am learning from the samples I received).

I double checked my measurements and it is definitely 30x117. The radius is 2.5 to 3 mm. I could mail you this sticker if you want something to work from.?
 
Joined
Nov 2, 2006
Messages
1,436
Location
Spokane
I double checked my measurements and it is definitely 30x117. The radius is 2.5 to 3 mm. I could mail you this sticker if you want something to work from.?

Thanks. Another member is mailing me one. That is very helpful.
 

CharlieS

GOLD Star
Joined
Feb 4, 2005
Messages
3,236
I have 3 of the above for husky


It would be helpful to have exact measurements with the sticker removed. I also need the corner radius to ensure the edge lines up correctly.

I'll trade one of mine for R&D, in exchange for a deal on a set of the new ones. PM me if you want me to send you one.

Here are some pictures:

43BFB475-C697-42ED-A282-9F0F8767FB7A.jpeg

0419F737-C2CC-4EF4-9968-FD8E1A624659.jpeg

191A4667-62F5-42DB-A55B-3FDA667AF089.jpeg
 
Last edited:

Markuson

SILVER Star
Joined
Jun 15, 2008
Messages
10,662
Location
San Diego via all over-
Keep in mind you will likely need additional 3M strips or glue to get these to stick properly due to the nature of the plastic on the mats. The other supplier's stickers have the same issue.

Should have samples next week.

That’s true.
Even Weathertech’s own sticker tends to come off under hard use. Both of mine are gone... :)
 
Last edited:
Joined
Nov 2, 2006
Messages
1,436
Location
Spokane
Ordering now open for Husky and Weathertech decals through October 11. $20 for a set of 3 including shipping. See this thread for more info:

 
Joined
Nov 2, 2006
Messages
1,436
Location
Spokane
Thanks to @Sandroad (PM me your mailing address) for mailing me a Weathertech sticker. I now have both stickers sized perfectly. Here is the Weathertech next to and on top of a proof print off my printer. Get your orders in by the 11th!:


20191006_161700.jpg


20191006_161731.jpg
 
Status
Not open for further replies.

Users who are viewing this thread

Top Bottom