- Location
- United States
*****SOLD*****
putting my rig up for sale.
1984 FJ60
SOA 2.5" springs
37" MTR's maybe 20% left
15x10 street lock wheels
TPI 383 Chevy. running rough. was rebuilt about 3000 miles ago. had been running perfect. likely needs a few new sensors. may be easier to remove the TPI and put on a manifold and injection throttle body. has been referee'd in California and smogged numerous times. it has been on Non-OP for several years now as I have several other cruisers. I've driven it all over and it drives well on the freeway and also walks the Rubicon no problem.
NV4500 5 speed with early 6.34:1 gear set. rebuilt less than 5k ago
marlin toy box 2.28 final crawl ratio of 160:1 (it idles through everything....)
19 spline t-case
front axle ARB 4:88's 30 spline Longfield axles
rear axle ARB 4:88's full floater rear end, poly performance cromo axles.
hub stud upgrade (see write-up) Full Floater Hub Stud Upgrade write up
track bar
marlin high steer
ARP knuckle studs
rear swing out bumper with tire carrier
front basic rectangle tube bumper
hydro-boost brake system
dual battery set up (painless) with in cab switch
aftermarket front seats
tuffy console
fenders trimmed
rhino lined rockers and hood
louvered hood
see my ROTW build for info and pics. Rotw Vette60
no longer has roof rack, or ARB front bumper. pretty sure you cannot even get a toy box for a 60 anymore. this is the ultimate manual crawl drivetrain. was a fantastic crawler that went anywhere with ease. will need some freshening up, maybe knuckle seals, brake bleed etc... from siting for a bit but its there. couple small dents, but not hammered by any means. time for a different project...
asking $8500. located in Placerville, East of Sacramento. I can possibly deliver for reasonably close distance.
Email me for quickest response. heavyfire@yahoo.com
putting my rig up for sale.
1984 FJ60
SOA 2.5" springs
37" MTR's maybe 20% left
15x10 street lock wheels
TPI 383 Chevy. running rough. was rebuilt about 3000 miles ago. had been running perfect. likely needs a few new sensors. may be easier to remove the TPI and put on a manifold and injection throttle body. has been referee'd in California and smogged numerous times. it has been on Non-OP for several years now as I have several other cruisers. I've driven it all over and it drives well on the freeway and also walks the Rubicon no problem.
NV4500 5 speed with early 6.34:1 gear set. rebuilt less than 5k ago
marlin toy box 2.28 final crawl ratio of 160:1 (it idles through everything....)
19 spline t-case
front axle ARB 4:88's 30 spline Longfield axles
rear axle ARB 4:88's full floater rear end, poly performance cromo axles.
hub stud upgrade (see write-up) Full Floater Hub Stud Upgrade write up
track bar
marlin high steer
ARP knuckle studs
rear swing out bumper with tire carrier
front basic rectangle tube bumper
hydro-boost brake system
dual battery set up (painless) with in cab switch
aftermarket front seats
tuffy console
fenders trimmed
rhino lined rockers and hood
louvered hood
see my ROTW build for info and pics. Rotw Vette60
no longer has roof rack, or ARB front bumper. pretty sure you cannot even get a toy box for a 60 anymore. this is the ultimate manual crawl drivetrain. was a fantastic crawler that went anywhere with ease. will need some freshening up, maybe knuckle seals, brake bleed etc... from siting for a bit but its there. couple small dents, but not hammered by any means. time for a different project...
asking $8500. located in Placerville, East of Sacramento. I can possibly deliver for reasonably close distance.
Email me for quickest response. heavyfire@yahoo.com
Last edited:
