my brake proportioning valve is stuck so i decided to disassemble and clean. i was able to take the nut off but not sure where to go from here. any advice appreciated.
1977 brake proportioning valve (1 Viewer)
- Thread starter jason ladd
- Start date
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.
RUSH55
SILVER Star
Check this out
forum.ih8mud.com
Proportioning Valve photos Disassembled
I took my proportioning valve apart because the rear drum brakes were locking up before the front discs. After cleaning all the rusty looking sediment off the internals, and brushing the inside of the housing with a brass shotgun brush, the brakes are much more reliable. Still not sure how it...
forum.ih8mud.com
brian
SILVER Star
or this:
Brake Proportioning Valve for '76 to '80 Land Cruiser FJ40
OEM style brake proportioning valve for '76 to '80 Toyota Land Cruiser FJ40. Prevent rear brake lock-up and bring back your brake performance. Reproduction of OEM part # 47150-14010. Plug and play replacement for your original valve. For vehicles with stock front disc / rear drum brakes setup...
www.cityracerllc.com
- Thread starter
- #4
thanks.Check this out
Proportioning Valve photos Disassembled
I took my proportioning valve apart because the rear drum brakes were locking up before the front discs. After cleaning all the rusty looking sediment off the internals, and brushing the inside of the housing with a brass shotgun brush, the brakes are much more reliable. Still not sure how it...
i actually saw this; however, per my photos, i dont see the spring and other parts in mine
brian
SILVER Star
- Thread starter
- #6
gotcha. so should i just order an oem style from cityracerllc in your opinion?
thanks,
brian
SILVER Star
yeap.
i was going to clean mine out, once i opened it, i noped out of that idea and just bought one.
i was going to clean mine out, once i opened it, i noped out of that idea and just bought one.
- Thread starter
- #8
purchased from cityracerllc. installed and fixed the problem. thanks again for the help. link below:
Brake Proportioning Valve for '76 to '80 Land Cruiser FJ40
OEM style brake proportioning valve for '76 to '80 Toyota Land Cruiser FJ40. Prevent rear brake lock-up and bring back your brake performance. Reproduction of OEM part # 47150-14010. Plug and play replacement for your original valve. For vehicles with stock front disc / rear drum brakes setup...
www.cityracerllc.com
The two rubber parts (piston seal and u cup seal) are available from muscle car research.
www.musclecarresearch.com
Other Products | Muscle Car Research LLC
Thank you so much for this information.The two rubber parts (piston seal and u cup seal) are available from muscle car research.
Other Products | Muscle Car Research LLC
I just ordered these parts. I just couldn't stomach the idea of $90 and up for this simple part.
Could you give an update on whether those parts fitted? I have a 87-89 (non-US) proportioning valve which may need re-sealing. Thanks.Thank you so much for this information.
I used them for my valve.
forum.ih8mud.com
Proportioning valve restoration
I obtained this a while back (thanks @65swb45) Tore it apart and cleaned it out, replaced the piston and u-cup seals with the kit from Muscle Car Research. Cleaned up the rusted end caps, tried my hand at home Ni and Cu plating (Instructables.com), I think they turned out pretty good...
forum.ih8mud.com
They worked great on my 3/1976 FJ40. I hope they work for you as well.
I used them for my valve.
Proportioning valve restoration
I obtained this a while back (thanks @65swb45) Tore it apart and cleaned it out, replaced the piston and u-cup seals with the kit from Muscle Car Research. Cleaned up the rusted end caps, tried my hand at home Ni and Cu plating (Instructables.com), I think they turned out pretty good...
