Hi,
Short info:
Toyota Land Cruiser HDJ100 1999 model year. 4,2 diesel, AHC, IFS, ABS
I have recently removed the AHC suspension, and installed Old Man EMU.
in the AHC system, it is a load sensing valve that adjust the pressure for the rear brakes (that is my understanding):
when i say i...
Rare part. FT-style valve cover for 1HD-FTE engines.
Good used condition. Most of the paint has flaked off, so there is some surface corrosion. Will look great after media blasting and refinishing.
$500 SHIPPED.
Picked it up today and drove it 400 miles back to LA.!
First up is valve cover gasket change, heater tees, and tracking down a small coolant leak. Looking forward to putting some miles on her!
Where can I find a shop manual? Does Bentley or Chilton's make one, or do folks have an online source...
Hey folks, I'm working to adjust the valves on my 1HD-FT, and was wondering a few things. Hoping to get some advice from folks who have done this before. The backstory here is that I went to replace my valve cover gasket, and thought I'd adjust the valves while I was in there - but I'm quickly...
My 93 fzj80s PAIR valve lost a stud. The very small stud, holds one of the two secondary valves (marked in photo below) to the larger part of the valve. Somehow, one of mine backed itself out. Curious if anyone knows how to find the right stud, or if I'll even be able to get one in there. I...
Guys and Gals,
Check you PCV Valve/Grommet and replace it often. Cheap and easy when you catch it early. I pushed mine just a little bit long and it came out in two pieces, nightmare if it's brittle....I cut mine on the two sides all the way down before taking it out, stuffed the center with...
I'm gradually replacing my vac lines, and found another broken vacuum valve.
This one appears to be a temp sensor of some kind, it's under/by the thermostat?
Any help identifying it, and or where to get one is greatly appreciated.
One of the nipples is broken off, and it's covered in greasy...
So long story short everything in my front a/c chain has been replaced to new relatively recent. The rear had been capped so I got all new rear lines and a new rear suitcase (I don’t know what it’s called so gimmie a break) but I don’t replace the rear expansion valve which I think is the fail...
Do all Asian 2 barrel carbs for the 2F have power valves? I’m noticing that some carbs do not have the vacuum port at the top front and some do? My minimal understanding is that it takes some manifold vacuum to keep the valve closed and negative at open throttle to activate it?
Few weeks ago my truck developed a pretty bad knock that was coming from near the passenger side valve cover. Did a lot of research here and was convinced I was in for a broken valve spring and maybe a new motor. Turns out the belt tensioner had failed and was the source of the knock. Glad...
Hey all, I've got what appears to be a Dorman check valve and grommets (2) on my OEM booster but cannot locate a repair for the failed grommets. They fall out of the hole in the BB and I'm having to use gasket maker to keep it in place. I can't even find a source for the original parts for...
Hey guys - 1996 Prado 1KZ-TE
Day 1 - it cranked pretty quick but would start til after 3 tries
Day 2 -started up no problem drove to work, and left work, but when I parked at the post office, it took 20 min of cranking to start.
Day 3 - just does a fast crank but won’t start
Replaced the...
Hello all,
After going through hell and back to get the proper head for my 3B, I'm now installing all the valves and springs etc. I also ordered a pack of new valve stem seals to install as well, and I'm having a terrible time pressing them on. Unfortunately no where local do they have a...
Toyota 11213-61011 (valve cover gasket for 81-87)
new in packaging
Don't need it anymore and figure someone else can use it. Send me $10 to cover flat rate envelope and it is yours. (Normally ~$25 plus ship and tax from Toyota Parts Deal)
Today read about this on a FB Toyota Lexus page. Is there a heater diverter valve and if yes, a point of failure? Besides the infamous T's, its a mystery unable to sort online.
Would y'all consider this enough oil seepage to warrant a new gasket? I already replaced the passenger side, but left the driver side as-is bc it was so much more difficult to access the bolts and I would much rather not deal with it.
this perspective is through the driver side wheel well...