I recently listed my 1989 Toyota 62 Series Land Cruiser on BaT, but I did not hit the reserve. Luckily, I get to drive for some more time, and it will give someone else the opportunity to hopefully buy this well built rig.
$52,000 - Sorry No Trades
Chassis: JT3FJ62GXK1113086
5.3-Liter L83 V8...
PCV valve for Toyota 5.7L V8, 200 Series LC, Tundra and Sequoia, new in wrapper. Part # 12204-38010
$5 plus shipping or local pickup Tucson AZ
Louis
lrowe_csp@hotmail.com
703 nine nine four 5816
So, my engine mounts are shot.
My car is a G spec 200 with a 1VD and manual box. Bare bones, UN spec, but it seems this bring some challenges.
The engine mounts on my car are oil filled but have no vacuum tubing. These mounts are only specifically fitted to my spec of vehicle, which is rare...
https://www.motor1.com/news/702983/2014-toyota-tundra-million-miles/
Original million mile Tundra was powered by the 4.7 v8 in the 100 series LC. Happy to see similar longevity from the 5.7. He needed a new transmission at 760,000 miles.
For sale is my fully built, off-road ready 2004 4.7L V8 4Runner Limited. I purchased this in metro Atlanta in July of 2018 @ 131,624 miles from the family who purchased it new. I am going to be moving onto another project and it’s time to send this off to a new home.
I’m going to include a link...
Hello, have spent some time here lurking in the past but figured I would sign up. Old man was a boat builder, learned to weld and work on stuff before I could reach the pedals, ended up getting a degree in motorsport engineering that I don't use.
06 4Runner V8 sport edition.
Picked it up...
Hi guys
As some have already seen in a previous post, i am going to buy a V8 2023 Model V8 Troopy (VDJ78)...
So the vehicle is ordered and should arrive in January....
Since i am using it for towing and offroad traveling i will do a custom dyno tune (expecting maybe 250-300hp at the flywheel)...
This is a new, unused power steering pump hose for a V8 swap. One side fits Toyota to GM power steering pump. This u it is made by Mosely Motors.
Asking $125 w/ shipping
Open to offers
Thanks, Jason
New, never used firestein bolt on frame mounts for gm v8, $175 shipped. Complete, NOS Downey rear mount set up, $200 shipped. Prices are what I paid it and what I want for it.
Thanks, Rick
Greetings all!
I have a 74' FJ40 with a Chevy 350 V8 that I am attempting to install power steering on. I am running into some interesting issues. Searches have led me to all sorts of extended research into what could be the cause of this misalignment but I have yet to figure out what is...
Hello - new'ish to the site so forgive me if I leave anything out. I now own a "fleet" of Toyota/Lexus 4WD vehicles and need to get rid of our beloved unicorn, the 2007 V8 4WD 4Runner Limited in metallic silver with gray leather interior. This was going to be my "restore it to new" project...
Looking for a 2006-2009 Toyota 4Runner and must have the following requirements:
- Be a Limited Trim
- Have a V8
- Has to be 4wd
- Rust free
Budget is 15k-20k. I live in Texas but willing travel.
I want to make sure I have all the lines hooked up in the right spots between the two heater cores, shut off valves and water pump. Couldn't find a thread that covers it but this thing is notorious for head gasket problems and im trying to eliminate things.
New, unused, never mounted. Open box. Gaskets included, which did not come with the headers.
$950 shipped or $850 picked up in Denver.
You’ll get these a lot sooner than waiting on DT to do a production run. It takes them months to ship.
I don't like my exhaust set up, it's duals hanging low off each side. I don't care for the look or the sound and I want to change over to a single exhaust and muffler exiting the rear of the truck. My set up is a 350 V8 with rams head exhaust manifolds so I think I am part way there. I have...
It hasn't been that long, only a year or so sitting where I left it. As a background, my dad bought this 2003 LC100 V8 in 2011 from a company owner that never went offroad with her, neither did me or my dad till recently. This car has been serviced at the local Toyota dealer but the repair bills...
My 3B swapped Fj60 has a PTO winch, and I am am planning a V8 swap in the next year or so. Has anyone managed to snake the PTO shaft past a V8 in a 60? I can't see how it will all fit, but I thought I would see if anyone knows of it being done.