tie

Does anyone know the diameter and thread pitch if the inner tie rod? I have not been able to find any specs in my searches. Any info would be greatly appreciated!

Any input or opinions on the best tie rod end kit. Any difference between say a OEM kit from Cruiser teq vs the heavy duty kit from Manafre? Appreciate the advice. Thanks

Just replaced the tie rods ends. First, the part numbers below match with the dorman parts I found on rock auto. Total at the time of purchase was $64. I did a terrible job measuring the tie rod lengths before removal. Also, had to clean up the threads on the rods quite a bit before...

I'd like to get these in fairly quickly. My normal sources are out of stock or double the price - City Racer - out of town until 1/19 - $85 - Cruiser Corp - $77 but out of stock - Cool Cruisers - in stock but $145 - Cruiser Teq - odd but doesnt have any FJ40 tie rod kits - Amazon - $140 -...

Wanted fj40 steering drag link and tie rod. I recently purchased a 73 fj40 (basket case) that is missing the steering linkage from the manual box to the axles. Any condition will do, rusted, bent or bad tie rod ends are ok. I just want to be able to steer this pile around while I’m pushing it...

Looks like I found an unexpected weak point in the tie rod end connection to my pitman arm when using a puller. Is a BFH really my only option to try to get this out at this point? I’ve given it a solid effort with a hammer to no avail. Once I get this out I’ll be ready to get my new ends...

Ever see this before? I’ve heard of bending the tie rod but not it breaking like this. Looks like it napped right where the link ends. Thank goodness this happened when pulling into my garage but so bizarre. Who makes the best replacement rod kit? Might as well upgrade but I don’t need...

What's up guys My 2000 LC's steering wheel is shaking badly on potholes, even the ESP started to react and break without my control. I did the 3-9 and 12-6 inspections it seems that the inner tie rods are loose on both sides (6-12 is fine) and there is an oil leaking from the driver-side boot...

Good Morning All! 275K 2000 land cruiser. Just purchased recently, 2 inch lift. I have been adjusting the torsion bars in front to get the ride height correct, 21.5 inches hub to fender on passenger and 21.75 on drivers side (finally got it!). Also was able to successfully adjust the panhard...

Im looking for a set of EMF Rod Ends; Thanks

Hi all 2008 HZJ71 1HZ LHD , someone know the tie rod lenght ? should be approximately 1184,00 or 1203,00 mm ? thank you Giacomo

I'm in need of an 80 series tie rod ASAP. please PM me if you have one and how much you want

I know one side is left hand and one side is ride hand threads which is which coming up empty on searches Thanks

Just replaced my TREs on my 80 and noticed my tie rod has a slight crook in it. Is this for differential clearance or is it supposed to be straight? Better to know now so I can easily remove the TREs without a pickle fork. Thanks in advance! -Phil

The mechanic gave me an estimate of $475 (parts & labor) to replace all 4 front tie rods. Does this price look fair?

I want to add two pairs of gear tie-down rings to the cargo bay floor of the FJ60. Two of the locations are right over the boxed in floor support immediately aft of the wheel arches so no bolt thru. The other two points I can drill thru the floor and use bolts. Question #1: Does anybody know...

In the middle of doing some work on a 100 and noticed something you guys may want to know. I replaced a rack and pinion with a reman unit, remans come with inner tie rod ends already installed. I screwed the outer on and noticed it was lacking the range of motion the original had, as in...

Looking for some assistance!!! I am replacing both ends of my tie rod and of my drag link on my 76 - 40 Series with NAPA parts for that year. The only one not matching up, of coarse, is the tie rod end that connects to my saginaw steering pitman arm. Can someone point me in the right...

Never seen this before...

Hey Gang, Just looking for a few suggestions on were the best tie rod end kits are?? SOR? Man-a-Fre? Cruiser Corps?? any suggestions would be sweet! Thanks