I'm looking for a tutorial w/pics or a video on replacing the starter motor in 1985 FJ60. I've searched here and can't seem to come up with anything. Does anyone have a suggestion? is it my boomer-level lack of search skills on this forum? is this such a basic task no one believes a tutorial...
For my 2001 LX470.
I'm about to buy a set of these:
https://spartanpower.com/product/jumper-cables/
But what AWG is required? I think the 20 ft ones would be more useful, and then I'm looking at a voltage drop calculator:
https://www.calculator.net/voltage-drop-calculator.html
But I don't...
I turn the key to start......wait a few seconds.....then, most of the time, it starts. After it runs and stops, sometimes 1, 3 or 4 or 30 tries and it starts. Maybe it's worse when it's humid.
I just don't understand the time delay. I am replacing the starter again. Sometimes a jump start...
Thought I would share this as well, hopefully it helps. Pretty easy fix that anyone can do.
For a few weeks I had the odd intermittent issue of the starter not turning. There would be a loud audible click from the solenoid activating the gear pushing out, but no crank. A simple fix always...
So I have been working on a 1HZ/H55 swap in a South American FJ73 . As the wiring harness looked more like a decomposed rats nest I pulled that out and swapped a complete 24 volt euro spec hzj73 witing harness in it . I looked at all my best 24 volt electrical parts for this and put in new...
Hi everyone,
I got a 1998 1fz-fe 105 series with automatic transmission. I took it to the mechanic to get the alternator and the starter motor changed over the weekend. After I got my car back I immediately noticed that there was a grinding noise when I start the car. The grinding noise only...
Having a no crank no start situation. Full power, all accessories working, battery ok and connections seem fine. Just a loud click and nothing. Ordered a fusible link replacement and preparing to take out the starter. I had someone try to turn it over and noticed a hissing sound after the...
Hey.
Newbie here
I have an 83 HJ47 and Ive gone and bought a new starter motor for her. Which means the external relay is surplus to requirements. Is it an easy by pass for the wiring or should I take her into an auto sparky? Having no success with trying to find answers to this one. I...
used starter for 13bt. Was intended for a BJ 74. It was bench tested by RADD cruisers last year and I never installed it because I repaired mine. $350 Canadian plus shipping.
Cranking my 2002 LX470 takes several seconds - maybe something like 4 seconds.
Is this typical or symptomatic of some issue like fuel pump pressure, etc. ???
The cranking time is longer than either of my Camry, Isuzu, or Mercedes - those
seem to almost instantly fire up.
The cruiser hasn't been starting up as quick as she used to, being a Di she used to fire as soon as i flicked the key, now it cranks for a couple seconds. I don't know whether it is an air leak or a dying starter, batteries are only a few months old and it had a rebuild 10k/km's ago, drives mint...
working starter motor taken out of a 60 series Sahara Land Cruiser, difficult to see in the photos, labels states:
Nippodenso Japan
28100-47090
028000-7240
24V 4C 27
Price $150.00
Location Brisbane, Australia
Freight extra
My 2000LC starter is finally giving up the ghost and I have a the choice of purchasing a new Denso $95, or a rebuilt Bosch $115 at RockAuto.
Does anyone have experience with the Bosch. The Denso is the OEM product but I have had good experience with Bosch parts in the past and wonder if anyone...
I have an unfamiliarly new Starter Motor that looks a bit different than the old one and unfortunately does not have any labels on it that I can see.
So my question is simply, Where does the IGN START wire connect to my specific starter solenoid? This wire....
Where does it connect to this...