short

Dobrý den, jsem tu nový, potřebuji pomoc s Toy Prado J120, pojistka 45 v motorovém prostoru pro ABS/MTR má zkrat, když odpojím konektory od ABS vše ok, nevíte někdo kde problém může být v ABS, děkuji všem za pomoc.

Looking for the slee short bus for an 80. Thanks

I don't run my LC that often. In the summer it is out a few times a week. In the winter, I try to run it once a week or more. When I take it out, I usually go for a 10+ mile drive...more often than not get it up to 70+ on the interstate. Around town, I go 30-60mph depending the road. Is...

Pair $500 plus shipping.metal in great shape on both seats, just dusty from storage

Hoping someone can post a picture of the wiring coming out of this connector. I had a short and fried the wires so I can’t tell how to wire it back correctly. Also looking for this connector (male and female) if anyone has one. If not I’ll bypass the plug. Thanks!

May have an opportunity to buy bumper in Dallas. Anyone driving from Dallas to near KC anytime soon?

Hello recently purchased this fj defiantly has cool patina but also so series rust and 30 year old bond I am looking to either leave it alone or a quick cover up until I can do metal work properly at least 3 to 5 years away. NOT A 100 opposed to diamond plate quarters but reluctant...

I have a 2F engine looking for a short 2-groove pulley. Thanks

I have a pair of Aisin short body hubs red dial $250

A little back story, Truck was bought in California and now has 317,000 miles on it. Been a good performing vehicle, rust free but paint that was peeling. A few years ago the 10amp fuse in the relay block in the engine compartment blew and I lost all interior lights and the radio. New fuse and...

I finally got to replacing my engine mounts, but on my first test drive a fuse link popped (battery terminal - black to white). Got the new fuse link in today, but there is a nasty short. Started disconnecting my ignition switch and alternator, but still no luck. I have removed all the fuses...

Swapping the knuckle and spindle from a 1981 mini truck onto my 1972. First, I am using the spindle from the 1981, so that isn't the problem. I have in this order, knuckle, spindle, brake spacer (rather than the dust shield), gold shield. Using vented rotors. I know the wheel bearing traces...

Hey all, Im trying to piece together a super short driveshaft with a steep angle. Ive got a 4runner double cardan front driveshaft but it seems like the cardan head is pretty lengthy (7.5ish inches from weld to weld). Any suggestions on the most compact double cardan I could replacethis with...

Pulled this 1FZ-FE out of a 94 with an engine knock at 150k. PO blew a HG and had the engine rebuilt (poorly). Engine knock is occuring in cylinder 6 with very mild bearing wear but within OEM Spec. All other bearings checked out ok. I didn't spend a lot of time troubleshooting as I replaced...

I have this set of Aisin hubs that I cleaned up. They’re the short body hubs that fit late 40s, 60s and 62s. I’ve assembled them and they work well. $125 plus shipping from 38305.

Open to trades or cash. Trading for '69 FJ40 parts.

Hello Folks! I've always had a temp gauge that sometimes like to peg itself out above hot, even though the truck is running fine. It will do it maybe once every 30 minutes, for 30 seconds or so. Not that big of a deal, but I noticed yesterday that the fuel gauge did the same thing (pegged...

Pair of short jump seats in good condition, I believe with original covers. Looking to trade for a pair of long jump seats suitable for a 73.

Yesterday I was having some issues starting my 60. Disconnected the terminals and cleaned up all the connections I could. While doing so the double eyelet for the fusible link feel apart from corrosion. While messing around with that I noticed that the large black wire (small black FL wire)...