rocker

Hi everyone Can someone tell me where this part goes? Part # 61414-60020 “reinforcement” I thought it had something to do with the rocker panel cover but I’m not sure. I have taken all the cladding off the truck and have not seen this piece.

Might be a tall ask. I am looking for the electric rocker switches specifically for a bj74 right hand drive. Not sure if others will work. But I need the power windows and door locks of the drivers side and passenger side. Yeats ago I did some custom switches but it never quite worked out and...

Very nice extra set of snake blinders. $500 plus shipping.

Replaces the garage door controls or sunglass holder in tan 100 series Land Cruiser or LX470 Never installed $70

I have a set of the RCI steps arriving soon. 5* angle with tread plate. Looking for how much anyone trimmed from the plastic rocker trim on the front and rear. Currently, I've found 4" on the front and 2.5" on the rear as measured from the top of the plastic. Any advice is welcome. From the...

Full set of mud flaps in excellent condition $500 Set of Chrome Rocker moldings - snake blinders $500 Photos will be posted shortly. Orig Brown FJ62 Dash Pad in excellent condition $600

Working on a resto and the interior was coated with bedliner. Water got under it and the pinch welds on top of the rockers where the bulb seal attaches were all rotted out from the inside of the truck. Looking for 4 cuts from the door areas - top of rocker, pinch weld to the floor pan. As...

I started a thread in paint and body but seems there is not much traction over there. So I’ll put a link here if it shouldn’t be in this section feel free to delete. Thread 'Rocker replacement' Rocker replacement - https://forum.ih8mud.com/threads/rocker-replacement.1327077/

Going to be replacing my rockers soon. Looking for some knowledge about the body structure. If I cut out the whole rocker corner to the floor could the body twist cause door closing issues? This would be the section being cut out. Should the area be braced or can I just remove with out issue?

Cross posting from the 20 series section https://forum.ih8mud.com/threads/early-f135-cam-rocker-bolts.1324507/

Working on reassembling the early (1960) F135 engine for the FJ28 “Lara” project and found one of the rockers cracked and some bolts stripped. The rockers are extra tall, almost 3”. I’m not sure how late they made the engines like that, but mid-60s at least were shorter. Bolts are about 5.75”...

I've got a single rocker trim molding ''snake blinder'' for the passenger side of an FJ60/FJ62 for sale. Good condition - one minor dent and has been wet sanded/polished with 5000 grit sand paper. Includes both end caps No fastening clips included For sale: $225 (free shipping USA)...

Where are ppl getting above work done in Hampton Roads / VA area? My 94 LC needs some TLC. Thx!

Have Driver/Passenger 4plus rocker protectors. These were originally powder coated from 4plus.I sandblasted and then coated with Black Raptor Liner which has been removed.They are currently bare,blasted steel. Will ship anywhere in US at buyers expense or Pick up in Long Island,NY. $375.00

I am in need of rocker shafts for my August 1970 FJ40. Rear is badly worn. It measures 12 and 7/8". Need that one but will take both if they are in good condition. Please help.....thank you. David.

Hi. Trying to adjust my valves on a May 1973 F engine. Got it at top dead center, but a couple of the lifters are up when they should be down. Which makes me wonder... Am I looking at the correct valves? For example, valve 7 is open when it should be closed. Maybe I've got them in the wrong...

Does anyone have a drivers side rocker chrome trim piece in extremely good condition that they want to sell? I bought 2 new passenger side trim pieces from SOR and they said I could switch them around. They pointed out the screw hole at the front of the trim piece on the passenger side would...

hey guys. I'm searching for some good pics. @Lil'John has a great thread for when Don did his. Cutting and tubing the rockers Lots of old threads lead to dead Birfield.com links or refer to NLA Iron Pig stuff. We are doing the rockers all the way to the rear bumper on mine and need ideas...

Hey Everyone, I have recently noticed a significant amount of water accumulating in the frame of my 2005 LC. At first I wasn't sure where but my mechanic said the water (literally gallons) was in the rocker panels and he was able to drain it by pulling a plastic plug on the passenger side. I...

I looked at an lc today and both side rockers are bubbling from road salt stuck between them and the steps. The frame, rest of the body, and interior looks good. its well below market price around here and the seller was quick to lower the price even more.....but a lower price doesnt solve the...