Looking to buy a stock take out ring and pinion from a 100 series. Hoping someone re geared and kept their stock gear set. This is for the front diff only. Will pay for shipping
Is it a remedy for excessive ring gear run out (0.005 [measured 70,000 miles ago] when the specified max. is 0.0028) by replacing original side bearings with 266,000 miles on them, but never abused in any way, with new bearings?
Would anyone happen to know if there are high quality HIGH profile rear ring gear bolts? (And front I guess too)
I struggled and messed the bolts up taking them off (there was about a 1/10th of a bottle of loctite on each bolt, like almost a jolly rancher’s worth)…
and then when reinstalling...
Does anyone know if the O ring on a 1hz dip stick tube is just a generic O ring? Part number listed is 96721-19010
Mine appears to be leaking and making a huge mess.
Thanks
I took my truck out for a shakedown run and heard a big clunk from the rear of the truck, when I got home the rear Duff was leaking. Turns out the bolts on the rear ring gear had loosen up and this is what I found inside. Several broke bolts and the rest loose.
I plan to add a locker in the...
Good day! Does anyone here know if a 2003 Sequoia is supposed to have a light around the ignition key ring? I saw a Youtube video how to replace the ignition key light bulb for a 2007. If the answer is no for the 2003, can the ignition key cylinders be swapped across year models?
Second Q is...
For sale, 60 series ring and pinion. Front set shows little to no wear at all, rear has 230k miles, looks polished on the teeth, one chip on the pinion end. Both ran great with no issues, I re-geared and like the new ratio with my setup. Missing most of the carrier bolts. $300.
EDIT: Top...
Brand new in box. Never used. These came with a Land Cruiser I recently bought, but I don’t plan on using them. Ships from Tulsa, OK.
Nitro gear and axle
T8r-488r-ng
$220 plus shipping
Nitro gear and axle
TLC-488-ng
$200 plus shipping
G'day all
So I'm looking for a piston ring kit for my 3B motor out of my bj70. I live in Western Australia Perth, if anyone can help werther they know someone or can point me in the right direction would be terrific. Cheers
Hello All,
I have a 71 FJ40 with a 2UZ and an H55f on 35's. The truck drives fantastic but 5th gear is almost unusable, nobody needs to go 100mph in a spring over 40! The current ring and pinions are 4.10. What would you recommend? And since everyone likes a picture...
I got 35" on and the front driveline coming.
I know R+P gears (I believe 4.88 is the correct set) is the standard way to go but some guys do the 10% T-Case gears instead. How much cheaper is it to go this route after labor etc? Is it a band-aid solution or is it preferred to solve the...
Anyone have experience using this gear:
https://yankum.com/collections/winchline-accessories/products/offset-winch-ring
Long but interesting video showing how it's used:
After years of surfing this site as a guest, I finally joined. . . .
I have a complete set of NIB parts from JustDifferentials.com for replacing the front gears (4.10) in my 1993 FJ80 (with front e-locker). I bought the parts a while back, but I didn’t end up needing them. I could use the cash...
I found out that the O ring of the 2 tubes/manifolds that go into the AC compressor are leaking. I found the part at one of the vendors for $1.99 but they wanted $10 to ship it and they suggested I get it locally. Does anyone know the part number or size so I can get an exact match locally...
Good afternoon all,
Really silly question here.... A saw a synchronizer ring listed for a 3 speed 68 -74. I know a 71 is not a synchro trans. Would I be able to add just the ring to make it a simple synchro trans if it list 68 and up 3 speeds.
Thanks and sorry for the dumb question.
71 40...
I was putting together the knuckle rebuild last night and noticed I am missing parts included in the FSM diagram. I bought a rebuild kit and assumed they would be included.
First, I'm taking about the back side of the knuckle assembly.
I'm missing the metal split ring, that is supposed to be...
Moved up to 5.29 r&p on my 96 lx450 with about 210k miles. I had bought the rig from an elderly couple that were the original owners, and it was in stock condition when bought. So most likely "easy" miles.
$40 each set plus shipping or make me an offer
Arroyo Grande, CA
To ih8mud members in Utah: I need a referral for getting my new lockers and ring & pinion installed in my FJZ80 3rds. Can anyone recommend someone that does a great job for a fair price? I can take the 3rd anywhere along the Wasatch front. Thanks in advance.
I just got my differential back. Before I put it in I noticed that there was no paint on the ring. Should I be worried? I always thought that the paint on the ring was used to show that the pinion was running centered on the ring.
There is no paint to show where it is running.
Should I be...