Hey guys,
So I have a manual GXL 2000 HZJ105r, great maintenance history.
Today I have noticed a constant clunking sound when in reverse, and it's only in reverse.
I select reverse gear, and it goes in easily. When I let the clutch out and start slowly I can't hear it. Once I speed up I can...
this may sound stupid but how do you access the reverse lights on a 2017 LX570?
it has some what I call push pins on each side and the bottom, but the top is stuck. do you just pull straight out? do I have access it from the inside?
i don't want to break it.
i need to replace that clear...
Was testing flex in my rear passenger suspension after installing the Delta panhard bracket..just wanted to see how much clearance I have at full flex
Anyway was reversing onto a hill and the truck just wouldn't go past a certain height..it ls like the reverse gearing only has so much power...
I’ve got a pronounced squeaking when I go backwards/reverse coming from what sounds like the passenger rear area. Hard to tell exactly.
Replaced all the pads and front rotors. Replaced the parking brake shoes even though they looked fine. Replaced right front caliper, unrelated. Greased the...
The factory reverse camera in my 2007 Tundra quit working all of a sudden. I checked and cleaned both connections, the one in the tailgate and the one in front of the spare tire, that didn't fix the issue. I also purchased a new aftermarket camera from Parts Geek, that also didn't fix the...
Ok guys, some of you may have seen my previous post regarding my rear camera / rear view mirror replacement project.
Well, had to fine tune a couple of things and replace some things 'cos they didn't quite work but I now have the project finished and I'm very happy with it.
I had to replace the...
5.3 V8 4L65 Transmission
After the stand alone harness install my reverse lights weren’t hooked up by shop. Found the 12 volt circuit wire working proper off the ECU curious of appropriate place to tie the 12 volt signal into that circuit to trigger the 2 tail bulbs. 4L65 NSS works and...
Morning,
I hope someone can assist. I have recently been having an issue with my cruiser. When putting the car into reverse - the engine revs drop and the car stalls. It seems to be made worse if the steering is fully locked. Normal driving is fine with no problems with dropping revs when...
Hi folks, we have a HZJ 75 that came from South America. Figured out why the reverse lights don’t work, the reverse light switch coming of the transmission is not wired to anything. From the info plate I know that it originally came with an H41 transmission but a previous owner installed a H55...
I will start by saying I have searched the 80 Tech Forum and read through five complete threads and partially through several other threads. All dealing primarily with a intermittent "No Start" issue which I do not have. Most deal with the Neutral Safety Switch (NSS) and or it's connector (p/n...
In a process of installing aftermarket stereo. I need reverse light signal for rear camera. I also need turn signals for side cameras.
Yes, I can get it in a back where taillight wiring is, but ideally I'd like to find it somewhere upfront. passenger or driver footwell area?
If you can point...
Got a 94LC inline 6 with 335k on her. Love the truck. Unfortunately it has a once in awhile, I ate up all you coolant occurrence. Happened 2 years ago and caught it just fine. This time after about 7-10 miles down the road, she got pretty hot. Noticed it, pulled over and turned it off. I let her...
I noticed I would blow a fuse when I would put my 1973FJ40 into reverse. Fuel gauge, the temp gauge and the oil pressure gauge must all be on the same circuit. Only when I would put the stick shift into reverse. Clearly the reverse switch is bad right and sharing a fuse with said gauges?
Hello,
I want to install this in my hitch mount. It looks like it requires removing the back end of the wiring harness and plugging the Diode Dynamic LED wiring between the 7-pin with the flap (back side) and the internal wiring.
Does the back of the wiring harness on my 2021 LC200 come off...
Need some help. 2007 Landcruiser 100 series, diesel, located in Central America, 170k, automatic.
I was backing up a hill fully loaded and it struggled and atleast 1 of the tires was smoking. Now reeves doesn’t work at all.
Earlier in the week I had been hearing metal on metal sounds when...
Hi all.
Looking to replace the reverse light switch on a 1970 FJ40 with column shift. What I pulled out is pictured below....not factory and I can't seem to find a replacement. If anyone can help identify this switch or suggest a way forward I would appreciate it. Threads look a bit bigger...
So what looked like a straight forward panel swap was not so straight forward. The sheet metal on the Prado is missing the holes for access to the reverse light bulbs...though the holes for bolting them in are in the right spots only with plastic fasteners in their place. (See middle of the pic...
I saw a mention of “*minor customization for drift shaft” …. What exactly does that mean? and I’m sure there’s an option with no drive shaft customization out there.
The reverse in my 94 (auto-tranny A442f) will not engage in 4H, but when I switch to 4L it works like a charm? I know 4L requires less torque to engage. But thats the deal? Bad flanges? Bad clutch packing? Bad tranny?