Hey all, I’m replacing my tie rod ends and am unsure how to get this bolt out that attaches my Dobinson’s damper to the tie rod. I’ve tried beating it out with a mallet. Also tried using the ball joint removal tool I used for the tie rod ends but can’t get it between the large washer and the...
The original car dealer glued his badge emblem onto the back door. See photo below. I have the prying tools but looking for guidance on how to remove the emblem without causing paint damage. Any guidance appreciated. Thank you.
Would anyone have any advice how to remove the OEM electric winch? I want to take mine out to replace the seals and so on. I can see the way to do it from Absolute Wits End rebuild pics, but I think it’s very heavy, right - so since I’m doing it alone, should I jack it up somewhere to support...
Was having trouble with the rear door handle removal. Ended up driving the pin holding the interior handle thru the plastic part under the chrome piece. Is this normal it chewed up the black plastic part when the pin was pushed out.
How do you remove the shifter from a H55? I spent hrs a year or more ago to repair something and now I need to remove again for a transmission swap. Yes the “locking” ring is removed, that’s easy. Thanks
Hi everyone
I have come across a stubborn bolt on both doors that I can’t get out.
Does anyone have any pics of these pieces taken apart so I have a better understanding ?
Thanks
hi everyone,
are there any tips and tricks to removing the plastic cladding off the truck?
getting ready for paint and thought i'd remove the stuff myself.
thanks
Crank bolt holding tools for Toyota/Lexus. Fits 100 series Landcruiser/ Lexus LX470/ GX470
4Runner/ sequoia/ Tundra with 4.7 2UZ. $ 159 both holding tool and handle.
Also for the following:
IS250
2UZFE
22RE
2RZ/3RZ
4L/4.3L/4.7L V8
3.0/3.3V6
working on a 1981HJ47 with a 2H
cracked oil cooler cover plate
trying not to remove the front cover
I searched and found an old thread from 2012 that said the gear doesn't need to be removed to remove the pump
can I remove the pump from the pump retainer, 4 nuts? or better to remove the pump...
do Not find seat removal possible even with tailgate UP.
WOULD find step by step instructions very helpful.
BTW: eagerly awaiting arrival of driver seat insert from Relax the Back. Will restore support and color choices allow good match to factory gray leather; $200 well spent IMHO
I'm trying to tap into one of the wires behind my fuse box like this guy to get some power to my new head unit in my Tuffy glove box but I am having trouble getting it out- when you take out the bolts its stuck inside and forward or backward the parts in the way look tiring to remove. Any...
I just came home after being out of town for a month and discovered my garaged 60 has some dings on the fender...the people watching my house are claiming they weren't aware of it or what may have caused it. 🤬😟
Whatever banged into the fender to cause those 4 dings also hit it hard enough to go...
I’m in the midst of restoring the dash pull knobs for my BJ40. Half the knobs have set screws…..the other half do not. Without a set screw in a knob, how are they removed? I’ve tried gently pulling and gently turning them to see if they thread off. They don’t / won’t. Seeking some...
I need help getting the fan and clutch assembly off of my 1980 FJ40. I know it should be dead simple but it will not budge. I have removed the 4 bolts, sprayed it with Kroil (for two days) and used the BFH as best I can. There are not a lot of options on hitting with a hammer. I have tried to...
Need help with removing clamps (
HEADLIGHT WASHER HOSE CLAMP
Part Number: 8527320020)
at washer hose, if you know how? Afraid to break plastic connectors. Thanks you . Turn to be using small tip flat screwdriver will do. Also wrong parts numbers for 2013 LX 570. Ordered 90075-91002 and 82711-16830 .
My clutch slave cylinder gave out, leaving a puddle on the floor under the passenger side. I bought a replacement master and slave cylinder since the recommendation is to replace both at the same time. I’ve been trying to get the hydraulic line off the master cylinder for the last 3 days...
Hi all, I'm manual swapping my 1994 KZN130 1kzte Hilux surf. Currently stuck on dropping the auto box out. Have pretty much everything done except for the torque converter/ flex plate bolts. I'm told there's supposed to be a access window in the bottom of the bellhousing. I have some foam there...