working on a 1981HJ47 with a 2H
cracked oil cooler cover plate
trying not to remove the front cover
I searched and found an old thread from 2012 that said the gear doesn't need to be removed to remove the pump
can I remove the pump from the pump retainer, 4 nuts? or better to remove the pump...
Hey guys i'm at a bit of a loss and just checking to see if anyone has any other ideas I could try before i send my injection pump or the whole car to a diesel mechanic.
So i've owned the 1982 BJ42 (Australia) for about 8 years with absolutely no issues engine related. Engine is (was) super...
My '91 JDM HDJ81 recently developed a drip from the injector pump, which seems to cure itself once warmed up.
I was planning to investigate the source, and temporarily reseal if appropriate, but then after a visit to the local Sam's Club I cut the ignition and she kept on running at very low...
Hello,
My 100 series diesel has no power when I accelerate and makes loud noises. The injection pump wiring harness was tampered with by the previous owner.
Toyota no longer manufactures this wiring harness.
Do you know where I can find one?
Thanks
toyota reference: 82121-60850
Hi everybody.
Thinking about importing JDM Land Cruiser HZJ77 to Seattle, US. It will have 200 k - 300 k kilometers. My previous (oversees) experience with not so young diesel JDMs tells me that some initial pump and nozzles will probably be required. So far I have made several phone calls to...
I have a 94 4runner 3.0 5 speed 4wd and have replaced a few 3.0s over the years and recently bought a rotted out 94 surf with a 1kzte in it and I’m planning on swapping the motor over in the next few weeks.
My only questions are:
1. Are the 3.0 motor frame mounts the same as a 1kz?
2. Can I use...
Any thoughts on whether or not this would work for a 2lt pump? Apparently my pump doesn't have the hole tapped from the factory. None of the 2lt engines in the US came with a tach so I guess that's why there's not a hole pre tapped, but I know basically every other country had the NA 2ls with...
Hi,
Second attempt at understanding what is going on here.
I'd like to hear toughts as to how it is possible for the timing marks on the crankshaft and the injection pump pulleys to not match up at TDC yet the engine still run?
Crankshaft pulley offset?
Injection pump pulley offset?
Timing...
Hi Guys...
I had a fuel issue on my cruiser... I had just completed a 4000km road trip... and then another 1100km road trip on the vehicle with no issues when 7 days later it was struggling to start, and eventually would start only after hand priming or push starting on a hill. This proceeded...
Have a 13BT with an upgraded CT26 w/ Garrett 60-1 wheel. Biggest issue is it’s slow to boost. Not intercooled yet not sure if that would help, but I started to play with the timing some today but I’m totally new to messing with Injection Pump timing. I moved the whole pump about a 1mm advanced...
So i put my engine back together after throwing a ton of new parts at it but as. i was reading through the repair manual i found that this knock pin goes in this area but i never put it back and dont even remember it being there, runs beautifully but should i be worried? 😞
Hi Mudders,
I'm switching from an IP that's equipped with an HAC, to one that's not. One difference is the throttle control arm that attached to the top of the IP and also provides the fuel control limit via a metal tab.
Unfortunately the lever from the non HAC pump is missing and I need a...
i cannot seem to find a workshop manual on my IP
if anyone have some more info about the pump and maybe where to get parts for it.
all info is appreciated
I have read all the injector pump leak posts on here I could find and whilst some are very similar I couldn't find someone asking my exact question...
There is diesel leaking out of the top of my 1985 BJ70 3B injector pump. I noticed it on the ground about a month ago and before I could find...
For sale is a 1-HDT diesel injection pump out of HDJ81. It was fully rebuild with a lot of brand new Denso parts in it so it's condition is nearly as brand new.
The pump is $1299.99 USD (core deposit of $700 is required)
Shipping is extra. Core deposit is returned upon receiving your old pump...