Hey guys, love this forum and all the knowledge shared. Has helped me immensely. Having trouble finding part number for this join in the exhaust, just blow the manifold, after replacing intake manifold gasket where there were a few leaks, hot box gasket that had a leak, I’m hoping this is the...
Hi guys,
An exhaust leak is making my 1/1975 FJ45 not so enjoyable to drive so it's time to get some parts ordered. Whilst this site is a wealth of knowledge, it can sometimes be information overload so can anyone tell me exactly what I will require to seal this thing up?
The plan is to...
Hey all, finishing up my head gasket and even though I bagged and tagged and took photos ahead of time, I still can’t remember where this bracket goes. Any help?
Is it neccasary to replace the Timing Chain on a 94 1FZFE when I do the Head Gasket repair ?
Also, why do people use a Cometic HG instead of a Toyota OEM ? Any Advantages.
I bought OEM MLS-type head gasket to my 1981 BJ42, part no. 11115-58110.
I assumed it’s just bolt-off and bolt-on. Then I found this from Radd Cruiser’s website: 3B & 13BT MLS Head Gasket 11115-58110-AM - https://www.shopraddcruisers.ca/mls-head-gasket-3b-13bt-11115-58110-am.html
Well, how...
Photos attached. 4/72 fj40. Stock as a rock. Rebuilt carb going on so I’m fixing vacuum leaks.
Can I remove these 2 head bolts and then put them back in /torque without causing any trouble? I need more access to replace the manifold studs. I guess I could re-torque all the head bolts per the...
Started up the FJ62 today. Blue/white smoke.
I’m located in Denver, what are my options? Head gasket rebuild?
350 + 5 speed swap?
Anyone been through this recently in the Denver area? Would love shop suggestions for either …
I normally just read and search, so posting is because system had that on the list. Hope everyone is well, I will be looking for info on head swap and what to do while I have it off for good measures. Thnx all
Toyota 11213-61011 (valve cover gasket for 81-87)
new in packaging
Don't need it anymore and figure someone else can use it. Send me $10 to cover flat rate envelope and it is yours. (Normally ~$25 plus ship and tax from Toyota Parts Deal)
I am about to start the heater T and hose replacement on my 2006 LX470. I pulled the radiator cab off just to take a quick look and found this portion of a rubber type gasket floating in the coolant. Has anyone ever seen this or does anyone have any idea where it may be from?
Hi All, I recognize there are many threads about this, but none that I've found seem to answer enough. I'm in the process of putting my motor back together, and when torquing the timing cover to what the service manual calls out, it pushed the gasket out. As other threads have suggested, I...
Sorry if this has been asked before, my search didn’t yield any info. Does anyone know where to find a gasket for a pre-‘75 idle solenoid? Do I need to make my own?
Also, I haven’t seen much on these earlier solenoids. Are replacements NLA or does someone sell them?
Thanks!
I have a gasket leak under the front water bypass on my 2000 LX470. I have a new front bypass, gaskets and a new water inlet. I plan on removing the throttle body to get access.
This new OEM water inlet has a pre-installed black gasket attached to the water inlet surface (photo). I have only...
Hey guys,
Did the tri mil header install on my 85 fj60, think the machining was definitely worth it so far as it’s all lined up evenly after some shimming and massaging Looks like everything is pretty level, but I’m wondering if it’s torqued enough. I went to 21 ft pounds (within the range...
Does anyone know where these go? There are two of these that came with a gasket set (manifold, oil pan, rear main seal etc.). Rubber impregnated cork.
I don't remember coming across these as I disassembled and cleaned parts.
Hello, I have recently purchesed a 1980 Toyota Pickup, SR5 Longbed 2wd, 20r engine. When I bought the truck the engine was only running on 2 cylinders, had a lot of carb problems, was burning oil, and possible head gasket. I rebuilt the engine, put on a new Carburetor (the weber 32/36) and...