gas

It takes two hands to take the gas cap off, like a stuck pickle jar. I rebuilt the charcoal canister and cleaned the ball valve in there. And replaced the gas cap. You can hear air rush in when the cap is opened. Any thoughts? 1997 Land Cruiser 80

Hey guys, back in August 2023 I wrote in I was throwing code P0456 (small leak in evap system) on my 2007. The code had now gotten more frequent. Gas cap has been replaced, smoke test shows no leaks, vapor canister was replaced, mass airflow sensor replaced and O2 sensors are in good shape. I...

Hass original stickers, great condition. $225 shipped.

Hey everyone, It's been quite some time since I've posted here, but there's not a community I trust more for questions like this :) I've been stick welding for a few years off and on and I just picked up Yeswelder 205 DS and intend to use it for MIG welding. I'm shopping for a cylinder of gas...

Hi. I am a new FJ40 owner. I removed my gas tank to deal with some light rust and am wondering about the holes. Are these supposed to be left open? Won’t water splash in and promote more rust? Thanks! Charles

I believe this set up is for the gas pedal linkage on the fire wall for an early fj40 or FJ45. Asking 40.00 plus shipping for all of it. Located in New Mexico.

This morning I went out to start the 80, and it fired up and ran just fine as I let it warm up for a couple minutes as I went back and forth grabbing stuff. Got in and switched on the headlights and it instantly died. Now it will only crank if I give it some gas, and will only run while I’m...

Asking about half of new, $600. Done by a local reputable shop where @Wadesters takes his restoration level tanks to get refinished. I can assist with delivery throughout the southeast.

Was parked in my apartment's parking garage but it's not secure whatsoever and located right off the street. Previously had a CAT cut halfway out before they got spotted and ran away, hopefully ya'll don't have my luck.

https://boulder.craigslist.org/pts/d/broomfield-toyota-land-cruiser-fj40/7698446664.html also includes free carb cooling fan. not mine- hope this helps someone

This only happens when in 1st and taking my foot off the pedal quickly. It seems to be an uneven shift into neutral. It doesn't happen in 2, 3 or 4. I'd love some thoughts as to what I should look at. Something in the transmission? Is it bad or not much to worry about?

I have previously posted my issue with my gas tank. Instead of repairing the rusty tank, I got a used one that was not leaking and the inside looked good through a scope. I decided to use the por's tank liner and all came out nice, looked real good through the scope. I installed the tank...

I am sure this has been discussed - I apologize if bringing up covered topic- she will start and turn over with a blast of starter fluid. Then cuts off- I was able to draw fresh gas from tank to newly installed fuel pump but cannot get the bowl to fill- a couple of caps of HEET in the tank with...

Team, I have a 2003 Lexus truck that has a fume problem. Gas fumes are present all the time but are especially bad when you fill the tank to capacity. Very little fumes in the cabin, only outside. Any ideas / suggestions on how to trouble shoot this? Wife wants to throw the damn thing away…...

87 smogged 2F: Upon removing the carb for rebuild, I spotted this dry rotted piece of plastic that has 3 vacuum hoses attached- sitting on top of what appears to be a typical bolt, screwed into the intake manifold… Looking into what it could be, found that it is the Gas Emissions Filter for the...

Need following parts for a 98-06 Toyota Land Cruiser Gas skid plate Both front fenders black in color Rear hatch outside handle And need this piece in picture cut out of the rear section of the driver’s side rocker Pm me if you have any of this stuff. Thanks Jason

Has anyone installed this in a pre-73 40? On their website, it states someone installed this in a 66 with minor modifications. Thanks

the metal part....

Ive been piecemealing our builder grade hvac/heat for 23 years now, and it may be time for replacement. I have a flame rollout switch that has been tripping the last two nights. My burners are oriented vertically, with flame rollout switches at the top and bottom. Its always the top rollout...

80 series gas pedal. $20 + shipping