filter

I took my LC on a long trip and while at idle for long periods of time (2 hours), the RPM's started getting a little rough. No lights, never stalled or ever close...but from a consistent 7-800RPM's at idle with AC, it would occasionally drop to 4-500 and jump right back up. It wasn't "rough"...

Can’t find the right size oil filter socket at local autozone, what size will work on factory filter? Thanks in advance.

All purchased for a 1967 FJ40 with an early 1970 block. This "kit" includes all you see in pics. Sold as a kit only 1. Kyosan fuel pump 2. Glass bowl fuel filter 3. NOS clear fuel line 90923-01042 4. compression fittings (4) 5. 6 early paper fuel filters for above 6. 9 early oil filter...

Finished restoring my 40 and have these part left over that need a home. No reasonable offer refused. Brian Johnson 425-213-4784 Brianljohnson@hotmail.com

Hey everyone, I want to start changing my own oil. With the exception of the oil and the metal cap removal adapter, am I missing anything needed for an oil change? Is the factory recommended 5,000 mile interval with full synthetic the way to go? Anything I need to look out for? Finally, what...

I was doing some work today and decided to check for the infamous dust seep issue that I've seen so many times. This is the first time i pulled my air-box out to inspect it and lo and behold there is a post-filter in the top cover and everything was squeaky clean. Zero dust ingress and its looks...

Hey there, today was the first "cold" day where I live, dropping down to 36 degrees last night, I have no clue if this has anything to do with anything but yea there's that. As for the issue, it started today just as I had pulled out of my driveway and popped it into 2nd gear my battery and...

Hey folks, I just posted up a little video that shows owners with the same NAV unit as my '04 LX how to adjust the Smog Sensor sensitivity. This is part of my new project called Lux Cruisers, which will be an information repository specific to the LX 470.

I’m looking for an inlet clamp for my FJ40. Anyone have a clamp they are willing to sell? Jeff

I’m finishing refurbishing my 1977 FJ40 OEM air cleaner. All seals are no longer available from Toyota. I did some searching and found that most people address the seal around the edge of the air cleaner cover with little mention of the seals on the top and bottom of the filter itself. To me it...

Hmmm. So there is what seems to be a genuine made-in-Japan oil filter 90915-30002, and a genuine not-made-in-Japan oil filter 90915-30002-8T (made in Thailand). No prizes for guessing which is the cheaper one. For anyone in the know, does that also mean the quality is significantly different...

Hello guys, I am changing my oil and bought a Toyota oil filter 90915-YZZD3 and it is tiny compared to the Napa 21515 filter. The Napa filter looks like it goes on a Caterpillar bulldozer and the Toyota is literally "cute" next to it. The seal looks to match but the capacity is way different...

Hey fellas, so I stumbled on this question when I picked up a paper air filter for my 12H-T 'Cruiser: Long story short, I have a thin Unifilter (read: oiled) foam sleeve that slips right over the paper filter. I figured it would be nice to have two levels of filtration. Is this approach...

I am looking for a paper element air cleaner that would fit an SD40 carb.

Can Somebody please explain to me how you get a 5 inch diameter filter to fit in between brackets that are only 4 1/2 inch diameter? The AutoZone VC120 is too large to fit in the oem bracket (which also mounts the VCV). If someone can chime in here it would be much appreciated. I don't want to...

I'm looking for the stock bracket that holds the lower fuel filter (between the tank and the fuel pump) to the chassis. My unit is a 1974 FJ40. Dave Dillon buscando13@sbcglobal.net 619-929-1944

Can the oil filter from the 4Runner/Tacome/Tundra/gas Land Cruiser (Toyota: 90915-YZZD3) be used in the 1HDT engine? I have a lead on a box of them for a decent price and wonder if they can be used? Cheers,

Trying all over to buy the above for my cruiser but having big problems. Decided to fabricate one here in Kenya. Can anyone point me to a diagram for the oil flow that I can give to one of the engineers here? Cheers Mike

With the valve on the oil pan draining the oil is a piece of cake Changing the filter requires removal of the front skid plate with the ARB System So a thought, get bjowetts cab with the valve and Drill an access hole into the skid plate. Maybe a round hole with a 4" hole saw?? Either the...

I was hoping someone could help me out here with a diagnosis and hopefully, an easy fix. I noticed that the corrugated, bent portion of the air intake hose that is AFTER the air filter (probably a foot or so below the air filter along the air intake hose), but BEFORE the turbo, is wet with...