We've had an issue with the knuckle during our last trip through Bolivia. (LX450, 115K). Hope someone can help finding the solution.
At approx 104K the right-hand front knuckle was leaking. After dismantling we found that there was a groove in de drive shaft were the axle seal sits.
We...
Hi team, I need some help.
Today I fitted a new set of Blackhawk radius arms to the cruiser and now I have a vibration through the car starting from low speeds up to freeway speeds. Maybe some slight noise, but the vibes are fatiguing after a short while and once you know its there, they really...
I dropped off my drive shaft to get new u-joints and rebalanced because it was the cause of my driveline vibration. They were having a hard time finding the correct u-joints and after taking measurements they found that dimensionally these are the same as the factory oe joints that came out of...
So unfortunately my F motor gave up the ghost today and I am weighing the options of just putting in a 2F or going the full montey and going to the 2FE with an h42 5 speed and transfer case. would i need to change the drive shaft lengths in order to do this. also what other fabrication would I...
Howdy,
I have a solid PTO and a solid PTO winch I just need the shaft between the two and the shifter assembly. Preferably one meant for a 78’ or at least long enough for one. I’m less picky about the shifter itself, but I prefer the older 3 speed ones.
I’ll drive within reason, and pay for...
Got a few extra parts I need to offload.
1. Stock Radius arms with Slee caster correction plates. Arms could use new bushings $100
2. Stock drag link/tie rod with Dobinsons big bore damper. Ball joints/ends need replacing/repair. $50
3. Stock front drive shaft. In good shape as far as I know...
Hello everyone. I am planning to buy a new rear drive shaft for my the lX 470 2001. On one of the forums I found information that it can be replaced with the original one from the TLC 200 diesel version, without any changes. It is changed because splined is much thicker. Has anyone had such...
I need one stud for my emergency brake. Size is an M8. It is for a 1965 FJ45 LPB. I have not checked with Napa etc... but if someone can tell me if they might have it that is what I will do. Just thought someone might have an extra or can point me where to get one. I am located in Newnan...
I need one stud for my emergency brake. Size is an M8. It is for a 1965 FJ45 LPB. I have not checked with Napa etc... but if someone can tell me if they might have it that is what I will do. Just thought someone might have an extra or can point me where to get one. I am located in Newnan...
I have vibration that gets pretty noticeable around 60mph.
It feels like it is in the back.
Steering is solid and no vibs in steering wheel.
Had this before I put new tires on and balanced.
I checked the drive shaft and found about twenty thousands run out on the barrel and the yoke is so...
Pro Tip of the day -
When measuring your drive shaft length for purposes of ordering a better one from Tom Woods, measure twice, maybe even three times. Use your best penmanship and make sure you can read your own damn notes. Then before pressing send on your order; go ahead crawl back under...
So I finally decided to pull the trigger and get a Tatton DC forward drive shaft for my LX450. I went with CJ Tatton given I heard great things about the quality of his work. When I tried to install and connect the CV to the T-case it would not slide into place. The CV’s circular holes would...
Hi there,
my cousin gifted me his 91 Land Cruiser when he passed away last year. Do to logistics, and repairs, I just got it. The LC was in Montana, then hauled to Washington, then finally transported to my house in CA, I had a transmission, and new drive shaft installed before I had it...
Front Drive Shaft off of 1996 Land Cruiser.
After going from 2.5" lift down to 2" lift the front shaft started a barely noticeable vibration around 70mph. I figured it might have been the u-joints settling into their new position so I installed brand new Toyota u-joints in this drive shaft. The...
Took our 200 off roading and had a leak the next morning on the transfer case. It was dripping heavily and the transfer case was nearly empty by the time we got around to working on it. Thought the transfer case seal was leaking so tried refilling with fluid and the leak stop additive we've...
What’s up folks, got a busted rear u-joint and I’m driving to Oregon next week. I’m in need of a rear drive shaft. I’d be happy to buy your spare or borrow yours (+ca$h) if you won’t be using your 100 for the weekend between the 16-19th
I don’t really wanna be driving with my center locked in...
During removal of the trans/tcase, I accidently separated my rear drive shaft. There wasn't an easily visible key or mark for putting the 2 ends back together, so does the degree of rotation matter? I assume not but I thought I'd ask before bolting everything up.
Thanks
Long time crawler, first time posting.
I have a heavy knock sound I suspect is coming from my front prop shaft. Only happens when front end is articulating over structure. Particularly when FLS is raised and FRS is down.
I have check all rubbers and bushings, everything looks solid, nothing...
Hi all, still very new to the 80 series.
If I install the part time conversion kit on my vehicle with a 6" lift on it, will I still need/want to install a double cardan drive shaft?
I've been reading forums that people have been installing double cardans up front just for vibration issues at...