Hello diesel crowd,
As the title suggests, I'm in search of guidance for adding a turbo to a Toyota 3L engine, mechanically injected and naturally aspirated. Specifically, a good friend of mine recently purchased a 1997 Dyna 150 with a 3L from a fellow who had imported it directly from Japan...
1997 Toyota Land Cruiser Prado TZ
RHD JDM AWD With 1KZ-TE 3L Intercooled turbo diesel. Automatic, PW, PDL, Tilt, JDM Sound System, Sun Roof, Power retractable mirrors..
Clean title. 71K miles
Within last 8K miles, new tires, AC compressor, full Ironman 4x4 2" lift specific for the Prado...
For sale is my ‘87 LJ70 Land Cruiser with 332,197 kilometers (206k miles) on the clock.
The truck is powered by a healthy 2L-T turbo diesel that generates plenty of power and low end torque.
The truck was imported from Croatia in 2019 by the previous owner. It has since been properly titled...
Hello all, yes this is a new account but I made it in order to post this engine for sale.
Asking $2000 and you figure out how you would like to ship or pick it up.
Originated from Costa Rica 1977 BJ40. Florida seller only did the import and title/registration and had very little information...
Decided to sell 1990 jdm 80 series. 1HD-T, auto trans. No rust, runs awesome. Factory integrated winch. Mileage is 222,000 kilometers. Timing belt due at 232,000 kilometers, have whole kit including water pump purchased from Back 40 imports. Also have brand new OEM radiator part# 16400-17030...
Hi all,
Look at a necessary engine rebuild on my JDM 93 Prado with a 1KZ-TE. I will supply this rebuild kit but was just quoted ~40hrs and $6k+ in labor. I understand it’s older so „pay to play“ is well known.
Is there anyone who might have different rates/time to rebuild or is this pretty...
bought this motor couple of years ago and to swap in my 88’ FJ62 but time and space has eluded me. I’m selling it for $2k and there is a bell housing that will match up to the FJ62 trans, a transfer case, and a radiator that comes with it.
Bj42 etc... OEM hood heat shield attachment arms. I bought an OEM hood 22 years ago from Toyota and it came with these mounting arms for BJ. I cut them off right next to the hood mounting point. Could be welded back to another hood for those of you that may need them.
Posting these on the Diesel and JDM section.
I have for sale 2 complete diesel gauge clusters for 80-series diesel trucks. These Tachometers are almost a must if you want to Tach to work after putting a Toyota Diesel Engine in your 80.
1. 80-series Manual Transmission Diesel Cluster (Note the...
For sale is an 80-series diesel fuel filter assembly with fuel heater.
Additionally, this has the pedestal mount (as shown above) to install it on the correct location if you are doing a Toyota diesel swap on your 80 (see photo below right in front of the brake booster). The mount attaches...
Afternoon.
Recently I put a new (to me) 3B into my vehicle. Today after bleeding the clutch and tighting off the bleeding valve the pedal has gone solid and doesn't disengage the clutch when the pedal is pushed in
LHD BJ70 with the 3B diesel. I added the turbo using the 13B manifold. EGT Gage added. Clean, no leaks, drives outstanding. I brought it back from overseas with me. I don't have the time to enjoy it so I want it to go to a good home. Asking @27,995.00 Please contact Summit directly as they are...
Hi all,
I'm in the process of identifying a fuel leak in the side of the diesel injector pump. I have removed a few components but am struggling to understand how to remove the nut in the photo. I have watched a few videos and consulted the repair manual but I feel like I need it explained to...
We have a 1983 BJ60 LHD Canadian G spec BJ60 with a 3B with an H55F behind it.
We were driving home and the truck started to lose power while driving (like it had a lot to start with). I was pushing hard to keep it running and revved up the motor with the hand throttle to keep it from stalling...