Hello all,
Does anyone know the torque spec for the crankshaft pulley bolt?
This is a 2007 Prado vx with the 1kzte diesel engine.
The pulley has delaminated. I have a new pulley and a homemade tool to hold it, but need to know how tight to install it.
Thank you.
Battery died, so I replaced it with a Duralast Gold 27F. + and - connections are correctly attached.
After I changed out the battery, the LC intermittently but regularly shakes and lurches at low RPMs and in tight turns, and lights dim. Once I give it gas, its fine, but the rythmic shaking...
I saw this video, the car has a 6.0 LS. What he does is drop the pan, then the crank journals, he then measures with plastigauge. He eventually taps the BEB's out and replaced them with new sized after polishing the crank. Can this be done on a 1997 Land Cruiser or do they not roll out?
So I searched and could not find this information. This is for a 1fz fe, I had a crank that had some rust on the inside threads and the M22 bolt would not thread in more than a couple turns before binding up. So I grabbed a tap and cleaned them out. For future mud members the bolt is a M22x1.5...
Looking for a decent crankshaft. Going to be getting machined so condition not a concern as long as it hasn’t spun a bearing too bad and isn’t super rusty on seal surface.
Also if someone has a junk crankshaft please reach out as well as I have uses for that too.
Getting ready to swap transmission/transfer between my 2013 and 2015 200s. Why? See my build thread. While I'm in there (my favorite words), I figure I might as well replace the rear main on the 2015. Do I need anything more than the seal itself (p/n 9031195013)? There is also a rear seal...
I'm doing the timing belt presently on my 2007 lx470. This is it's second belt change now at 189K (first done by a Toyota Specialty shop). Fortunately the teardown went well but presently I'm a little confused. The 2007 has a slightly different procedure for timing belt removal according to the...
Looking for 3FE Crankshaft pulley for a 92, not sure if the 60 series pulley is interchangeable but the part number is 13470-61030. The only one I found online is over $500-$750, which at that rate I might as well buy a new engine.
I have been dreading replacing this seal for a while, so I will tackle this project in the winter and document it. I have had difficulty finding clear instructions on replacing this seal while the engine is in the vehicle. I understand I need to remove the radiator, bib, etc., so I have room to...
Anyone know of a good source for crankshaft bearings? Motor is a 5/73 1F.
They keep getting put on back order. I'm hoping someone can point me to some that are in stock. Thank you!
Hey guys need a new crank for my 1hdt and been looking around and a factory crank is 3k and 3 month wait but there is some cheaper aftermarket ones around for about 1k to 1.5k and here by the end of the month. Has any one have any experience with the cheaper options or just not worth the risk?
Can anyone confirm that it is 30mm? Is there room for a deepwell impact socket on a breaker bar, or is an open-end wrench needed?
Needing to hold it still to remove torque converter bolts.
Thanks!
Looking for a useable crankshaft for a 78 FJ40 2F.
Machine shop said mine was bent .040.
I'm located in Washington state.
Thanks for any help.
(I am open to buying another 2f engine if there is any out there.)
Thanks
Description:
Crank Shaft
P/N:
13401-61010
Condition:
New & OEM (Carton not opened)
Fitment:
https://japancars.ru/TOYOTA/1340161010
( Press on applicability to show fitment )
Price:
$859.99
Shipping:
weight: 37.5kg
( contact us for shipping quote )
Looking for some advice here.
doing a full rebuild on a 22re for my 1stgen 4Runner. Machine shop just finished with my crank and informed me the rod bearing needed are +.040” (ouch!) and the crank is +.020”.
I’m already over budget and am inclined to run with this crank. Am I taking a massive...
Hey All,
I recently got an FJ60 off of marketplace that was known to have engine knock, and having rebuilt some VW 1600s in the past, I figured I could do a good enough job fixing the knock.
I popped off the oil pan last night, and lo and behold the rod bearing on cylinder #3 had turned into...
Good evening,
I am parting out spare working parts from my 1999 Land Cruiser 100 Series.
Spare used parts in-stock:
- Factory fuse box (includes all relays & fuses that are only 3yrs old)
- Factory Denso OEM camshaft position sensors (3 spares in stock)
- Factory Denso OEM crankshaft position...
I have a 99 Land Cruiser that cranks but does not start. The issue just started last week after I tried to move my LC from the front of my house to the backyard.
Last week, I started up (cold start, well it was 70 degrees outside) drove forward and then backwards to back into my driveway. Once...
Tracked a rattle down to an almost sheared crank keyway- Never looked, but seems someone left off the crank nut. So- need a keyway, nut, and lock tab for a 1988 FJ62. Currently stuck near Lava Hot springs, Idaho, I'd obviously pay for shipping to the local post office.
Or if anyone is local...