Going after the timing cover gaskets and seal and trying to scope the job. Can I do it with the radiator installed if I pull the fan and shroud? Will the balancer puller fit in the space? Any suggestions?
Thanks in advance.
Bob
Picked it up today and drove it 400 miles back to LA.!
First up is valve cover gasket change, heater tees, and tracking down a small coolant leak. Looking forward to putting some miles on her!
Where can I find a shop manual? Does Bentley or Chilton's make one, or do folks have an online source...
Looking for a heavy duty car cover. My truck will be sitting in storage indoors and i'd like to have it covered.
I have a Victory 4x4 roof rack and ditch lights on my hood.
Anyone make covers that would have extra space for my accessories?
Any help would be appreciated.
Hi everyone, after months of searching for the right 200 I was able to pick up a low mileage Heritage edition yesterday. I’ve been dreaming of owning a LC since I was in high school reading all of my Dad’s car magazines and buying guides. I’m so excited to finally be an actual owner!
The...
Hello! Looking to buy flywheel bottom cover assembly for my 1966 FJ45 (F-engine, 3-speed manual). I am in Southern California.
Offers and leads would be highly appreciated
Thank you!
Looking for a 1985 FJ60 radio cover plate. They used to have them on eBay and now I can’t find them anywhere, I don’t care if it’s authentic lol. Just need to get something to cover up the hole where the radio used to be. Thanks!!
I just installed a new Warn winch and I have no experience with them so I was just wondering if it would be a good idea to purchase a cover, or is it not really necessary. I'm thinking that it would probably be a good idea to protect my investment, but IDK. What say you all?
New OEM, part number 64739-90K01-B0. Application is FJ62 but I think should fit all 60 series.
$20 plus $9.50 shipping.
compare to Proffitt's 3d printed one at $50.
https://parts.resurrectionlandcruisers.com/products/fj60-3d-printed-rear-windshield-reservoir-access-cover
Found this wiper motor hanging in the rafters in my garage I am getting older and cleaning out! It is not tagged so I know neither the year it came from nor its condition. I know wiper motors are very hard to come by these days. Price $150 postpaid anywhere in the CONUS. Also found a wiper motor...
Selling this wiper motor I came across it as I was cleaning out parts hanging in the rafters of my garage. Tag says it came from a 97 80 series and is in good shape. Price $54. Buyer pays shipping. Best to email me shmukter@pa.metrocast.net
I have an extra fuel filler neck / fuel separator cover for a 40 series I don’t need. Not sure what years it’ll fit but it’s the same as the one on my 74.
$30 obo plus shipping.
Have this evaporator labeled from a 78 FJ40. It's actually in great shape and the two piece cover is very solid. Would like to get $65 for this buyer pays shipping or let's say $75 shipped anywhere in the CONUS. Best to email me shmukter@pa.metrocast.net
Hey!!
Back at my oil leak project.
My leak appears to be behind the timing cover backing plate right above where the oil pan joins the block on the drivers side. Hopefully what I’ll find when I remove backing plate is a gap in the gasket.
My question to all of those in the know-based on the...
Selling this 80 series gray fusebox cover it's in great shape all four retaining tabs are intact. $24 plus the ride. Best to email me shmukter@pa.metrocast.net
Toyota 11213-61011 (valve cover gasket for 81-87)
new in packaging
Don't need it anymore and figure someone else can use it. Send me $10 to cover flat rate envelope and it is yours. (Normally ~$25 plus ship and tax from Toyota Parts Deal)