carburetor

This is a 1982 FJ60 carburetor that has had the jets removed. I was present when it was taken off the truck, and watched another guy carefully remove the jets for a project. It is otherwise complete, as seen in the photos. Lots of great parts, or install jets and run it. It has been boxed in my...

Looking for a source for the screws that hold #1 to #3. Thanks

Taking a break from my ignition issues to ask a question about fuel lines. My "75 FJ40" does not have the original engine. (Or Carb :( ) There are 2 fuel hard lines bolted to the chassis rail under my hand. One goes to the fuel filter and on to the fuel pump. The other is in my hand and, up...

My 1965 FJ45 LPB (from Arizona) engine was completely rebuilt also the SD40 carburetor. Yesterday was fire up day. It started immediately, ran well and idled. When throttling up it would stall or run rough. Looked at all vacuum points and all good. Determined it must be with SD40. Reason being...

My 1965 FJ45 LPB (from Arizona) engine was completely rebuilt also the SD40 carburetor. Yesterday was fire up day. It started immediately, ran well and idled. When throttling up it would stall or run rough. Looked at all vacuum points and all good. Determined it must be with SD40. Reason...

Just picked up a '77. There is no air cleaner on it. Want to pick one up. I'm guessing this isn't the stock carb. Or if it is, it's finish has held up remarkably well over the years. I can't find a model number, only the serial. Is there somewhere special I can order an air cleaner for...

Do all Asian 2 barrel carbs for the 2F have power valves? I’m noticing that some carbs do not have the vacuum port at the top front and some do? My minimal understanding is that it takes some manifold vacuum to keep the valve closed and negative at open throttle to activate it?

I searched, yes, I searched. Before that I looked all through my Emissions Manual. 1978 (Sep '77 build date) Fed Spec 40. I had someone else under the hood for some work (film at 11) and they left a few vacuum lines disconnected. My question - where does this port - see blue arrow - connect...

I'm looking for a rebuildable California spec carburetor for my stock 2F. (Toyota 21100-61073).

Hi dudes, Is the city racer carb pretty plug and play? Opened her up and seems identicle, but wondering if anyone who’s bought this has some insight into the measurements and settings being roughly the same as the stock carb? (I also noticed the FCS is a different type than what’s on my...

Model : FJ45 1983 - stock I noticed recently that I had alot of engine vibration, maybe low speed, and the exhaust fumes were excessive. There's no smoke. Thought it was time to re-adjust the carburetor using lean median method. Set-up - Digital tachometer connected to the coil - Vacuum...

Carburetor from a 1979 fj40 Condition unknown probably need rebuilt $150 include s/h ( lower 48 - US) Note: closest carb. To the left in the photo not included in this post Thanks

I'm looking to return my 1977 back to the original mechanical linkage. When I got it it was set up with a holly. So I will need everything from the pedal to the carburetor including the bracket that bolts to the carb. The only component I still have is the bracket still attached to the firewall...

Believe this is year specific? to a 1973. 100$ shipped to lower 48

Who on mud is the recommended person to send a 2f carburetor to rebuild? Cost? or is it better to just buy a good aftermarket one like at cityracer? I am not sure mine is worthy of rebuilding but it is a oem carb. I started taking it apart but its a little out of my depth. here are some...

Just took this carburetor off my 1983 FJ 60 last week. My rig ran pretty good. Not perfect but started every time and no leaks. I replaced this with a Jim C. Rebuilt OEM Carb that’s the only reason I replaced it. I personally put a new secondary diaphragm on it and a new Carb Accelerator...

Hi guys, I bought my 60 (1985) with a weber carburetor that start leaking and now I want to replace it with the same one. Do you know what is exactly the model and where I can buy it? I know that cruisercorps sell the kit, but I was wondering if someone know where I can buy just the...

Hey guys, At the last line of defense here with firing this thing up. Rebuilt motor and whole project coming to this point. Carb was leaking upon initial firing yesterday, snd I think had a vacuum leak as well. so I rebuilt the carburetor again and it’s still leaking. Vacuum leak is resolved...

Greetings & wishing all 24’ be the best year of their lives!!!!!! Searching for windshield frame for my 1977 40 . Also need of a hood for same . Also best Soft top for same . New to this so not sure where exactly one posts for help/advice on carburetor issues. Recent purchase from Central...

Looking for a fellow 40 owner in central/South Austin ideally to take a gander and listen to my 40 and help me ensure I’m not f’ing anything up since I’m actually driving her a ton now. Drivetrain and engine tune is what I am mostly having questions about. I’ve been tweaking the carb (Weber...