I have a relative that repaired/restored Land Cruisers for a living. He has retired. This is the last 40 series he has. The body needs either the 3/4 tub repaired or replaced. Frame has some odd brackets from a prior owner that need cut off here n there. The 2f runs like a sewing machine. Fair...
I would like to sell the complete top to a single member who needs everything. Desert Tucson truck , minor surface rust except passenger rear door bottom. Paint in great shape, glass great condition, windows roll up and down, side pop outs work and latch.
1. Roof top, includes door frame top...
1977 Toyota Land Cruiser Pickup FJ45 4x4 powered by 2F 4.2L and 4 speed manual. The truck was imported from the Middle East and its title & was registered in Texas. No AC or Power Steering.
Mechanical Condition: Overall, this truck sounds good. The engine is strong and plenty of torque. No...
Hey all, first post. Been following this forum for a few months. Recently had an opportunity to pick up this BJ40 for $4k which is very reasonable considering where I live all vehicles are import taxed about 50%. However, as you will see in the pictures it undoubtedly needs some work. I've been...
Guys, I have a 1977 FJ40 with the single dome light (not currently wired up) by the driver's left shoulder. Scrubbing the forums and old posts, I think I'm accurate in saying...
1) Pre Early 80's FJ's had the dome light which was fed by 1 wire and switched at the light. There is no factory...
I inherited a 1977 FJ40. It hasn't run in about 15 years I believe but has been garage kept for at least the past 20-30 years. Where would you start with restoration? I'm looking to keep the original 2F engine. I am new to landcruisers. The frame is in good condition and has just a little bit of...
1977 Toyota Land Cruiser FJ40, 145k miles on ODO
$25k
Highly modified. Competent rock crawler that is still streetable. If you are a Toyota purist, it’s not for you. If you’re looking for a rock and trail rig this could be for you. Same owner for the past 30 years. This rig has evolved and been...
I have decided to sell my 1977 FJ40 Land Cruiser which I restored when I acquired it in 2015. I don't drive it enough and it just sits in my garage most of the time. I would love for it to go to a good home.
Location: Austin, TX 78750
Asking: $38K
Contact: David Gonzalez 512-791-7502
Specs...
Link to video.
Was going to use the axles and drivetrain for my LV but got the F motor running well on my LV and am keeping it stock. So selling this Ranch Truck FJ40 that I got as a donor. It’s a 1977 So. Cal vehicle its whole life. Solid tub (rear sill shot) but floors are rust free minus...
I'm looking to purchase a 1977 BJ40 import, but seller doesn't know where it was imported from. He provided a 10 digit vin but, i can't find any info with the vin.
Hello, I am looking to buy a VTV-vacuum transmitting valve that is Toyota part # 90925-01006. I need the red top with black body if anybody is willing to sell theirs or has an alternative that would be great. Mine broke as I was replacing all my vacuum lines.
This new to me 1977 FJ45 has a PTO and PTO driveshaft to the front, but no winch. Judging by the shifter mount, I doubt that the FJ originally came with a PTO winch - I could be wrong though. The shifter pivots forwards and backwards on a mount fastened to the top of the tunnel. The PTO...
Back when I first got Internet in 2003, I picked up this jewel (along with about a dozen others) from guys that had taken their stock carbs off back in the day for the ‘power pack’ aftermarket setups that were being sold when the rigs were new. Most of these guys ‘found’ their OE carburetors...
I am looking for the two air cleaner brackets that bolt to the valve cover on a '77 fj40. I have a good air cleaner assembly with the large bracket that bolts to the block but for whatever reason those two brackets are missing. Thanks.
Looking for the buckle portion of the 3 point front bucket seat belts. I've got the retractors and belts. I just need the buckles.
Also wouldn't mind picking up a rear jump seat belt setup.
Thanks
Thought I'd pass along my most recent modification to the forum. It turned out great and can be easily replicated if others want to do the same thing. Or better yet, share what you've done and show us all a better way.
I basically took a 1970s early style spare tire carrier and stripped it...