ARB front install?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jul 13, 2003
Threads
71
Messages
786
Location
Folsom, CA
I had Mudrack setup a ARB locker in a diff for me that I picked up on monday. It is a RD124 locker. It will be going into the front axle on my 40. My 40 already has a lockrite in the rear, which I like. I failed to ask Gary about a bag of parts I got with the locker. He is on the Con now and I can't get in touch with him. The bag included a bunch of C clips which I won't use on the front. Two other pieces included were an allen head metric bolt and lock washer and a small diameter long pin. I don't see where the allen head bolt would go. The pin looks like a 'cross shaft retaining pin', but I am not sure. Are either of these pieces used in a front install on the ARB? I am thinking not in the front. This is my first ARB install. I need to get this installed tomorrow and Wenesday. Heading in on thursday.
 
Cardinal, I have never done one in the front, but ARB lists (Full-Float Front Axle) Part# ARB RD33 as the correct one for the front. The RD124 is listed as for Semi-Float Rear.

HTH

Ed
 
http://www.ih8mud.com/cruisertech.php
contains the following two items:
ARB RD02 Full-Floater Install Instruction (Acrobat)
ARB RD08 Semi-Floater Install Instruction (Acrobat)

(left side, towards the bottom...)

hopefully, your answer is in there....
 
Ed is correct. I talked with ARB a few weeks ago to try and figure which locker I had, since it was 10 years ago mine was installed and the O-rings went bad, and they now have new models for the 40. The RD 33 can be installed in front or back of specific axles, but the RD124 can only be installed in rear. I just redid the O-rings on my locker and although not a RD124, the 5mm allen bolt with washer, and the retaining pin, slides into a hole from the non ring side and holds in the cross shaft. If you were installing it in the rear, you would only install this after you slid in the axles, set in the C-clips, and then once you put the rest of the innards in, you would insert the retaining pin into the hole, right down from the shaft, with the threads to the bolt side, and tighten the 5mm bolt to specific torque setting. If you truly have the RD124, then I'm not sure what you can do.

MudRak knows a whole lot more than I will ever about this, so I say wait till he comes back.
 
Last edited:
Gary Kardum does dozens of these ARB installs a year. So I know he would not give me the wrong locker. The instructions that came with the locker say it is a "RD124 Toyota 8.9", C-Clip" and dated 4/05 He said it would work either in the front or rear and can be switched on the trail if necessary( Something I would never want to do). Still don't know. My instructions read the same as in the Tech seciton.
 
With Gary out of reach, maybe we can get Poser to chime in. He set up mine for the rear and went through the install with me. He does a bunch of ARB installs and setups and could provide some real world advice. You might PM him, or call him at his shop.
Good Luck

Ed
 
Make sure you put the cross pin retainer in per instructions. If you don't, your cross pin will work out, it will catch on your diff housing, probably bend/break in half, shear off the output shaft on the transfer case, and punch a hole in your diff cover. All at roughly the same, inopportune, time.

Don't ask me how I know.
 
The RD124 will work for the front. It is the c-clip models that will work front and rear, it is just there is not a need for c-clips up front. Rd08 and rd124 work for the same applications. It is the full floating model, RD33 I guess, that will not work in the ReaR of a semi-float axle since there are not any provisions for inserting c-clips. It works on the front, or the rear of full floaters..

Special note, just make sure that the cross shaft retainer pin is inserted with the threaded end sticking out so you can actually remove it one day.
 
The RD124 is for a semi floating axel. These can be used on both semi floating axels and full floating axels. The only difference is that there is one less spider gear and a window cut into it so you can access the C clips for the semi floating axels. Since you have yours in the front (full floating) you do not need the thrust block, c clips and associated hardware. Keep this stuff in a safe place, you will need it if you ever decide to move your ARB to the rear.

I’m running the same setup, works great.
 
Poser to the rescue....agian. The answer is yes for the allen head screw and threaded pin.
Thanks Steve
 
Well heck, shows you what them ARB boys know....

They must use the literature from the ARB website to answer questions, since it shows that the RD 124, only works on the rear. They probably sold me the wrong O-rings too. I can hear it leaking already. Glad you got some expert help. Guess I will try these guys first next time too!

Brian
 
exrsa1 said:
They must use the literature from the ARB website to answer questions, since it shows that the RD 124, only works on the rear. They probably sold me the wrong O-rings too. I can hear it leaking already. Glad you got some expert help. Guess I will try these guys first next time too!

Brian


:confused:


Who is 'they'...ARB?



cardinal fang said:
Thanks Steve


You are welcome Bill!

Was good to talk with you!

Hope we see some pictures out here of this!


:beer:
 
Pics of install

Thanks to Poser, he pointed out where the pin and bolt are installed. Once you see where it goes, it is obvious why it has to be installed. It holds the large cross shaft in place and prevents it from working free over time.
I used a drill bit to make sure the pin was fully seated.
Then a little bit of red locktight on the bolt to make sure it stayed in place.
If you look close at the pin, you can see threads inside. This is the pin that requires the special tool from ARB that screws into the pin to remove it.
So the learning result here is that the bolt and pin are installed whether the locker uses the C-Clips or not. Front or rear. Also, ARB needs to make a better drawing or details of installing the pin and bolt.
arb locker.webp
arb pin.webp
arb bolt.webp
 
Last edited:
Poser said:
:confused:


Who is 'they'...ARB?






You are welcome Bill!

Was good to talk with you!

Hope we see some pictures out here of this!


:beer:
Yes, 'THEY' being ARB tech that I spoke to.
 
Back
Top Bottom