Time for front axle service (pics)?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jan 12, 2006
Threads
124
Messages
1,109
Location
St. Louis, MO
So after talking with CDan and others, I decided I would wait to change the rotors and go to 100 series pads until this fall (about 2,500 miles for my 80) when I have more time to do the full front axle service since switching to 100 pads now requires new rotors, which in turn require removal of the hub which seems to be at least halfway to a full front axle service. But I don't have the time before next weeks expedition departure and I don't have the parts ready.

Soooo, I changed the front pads today (super easy for this first timer 1/4 :banana:). While there a took a few digital pics and I'm left wondering a few things. First, why the heck is there so much crud on my knuckles given that I go through the local car wash weekly? Second, can I just take my pressure washer on a low setting and blast that crap off (should I use a degreaser first)? Third, how bad do they look? I should note, there was nothing wet or leaking, but the photos where taken after I sprayed some PB Blaster in prep for the brake line replacment with Slee SS lines, so I think there is some overspray showing in the photos.
Birf 01.webp
Birf 02.webp
Birf 03.webp
 
istockphoto_232274_terrible_two.jpg
 
Methinks you've put that axle service off long enough :eek:


Are your birfs clicking?
 
I wouldn't touch them until you're ready to do the work. The gunk isn't hurting anything, and removing it might cause problems- like injecting water into the knuckles or something. I highly recommend cleaning them just before your service.

-Spike
 
Cody: Damn that pic is funny - I nearly peed myself!

Methinks you've put that axle service off long enough :eek:


Are your birfs clicking?

Jeez, I was hoping for good news. Or at least news that the cruiser's two month (~2,500 miles) trip north for the summer would be no reason to worry and I could wait until late summer / early fall when I have more time.

No clicking of any kind. Does that change your diagnosis?

I wouldn't touch them until you're ready to do the work. The gunk isn't hurting anything, and removing it might cause problems- like injecting water into the knuckles or something. I highly recommend cleaning them just before your service.

-Spike


Ahhhh, just what I was hoping for. I suppose if I wait long enough somebody will tell me what I want to hear :). Sure, I may have to ignore alot of other advice . . . .

I think you're right Spike, I'll skip the pressure wash until I'm ready to tear it all apart in a few months. I really do hope there will be no problems during that trip. My 19 y/o daughter ("wrench? What's a wrench") is taking the cruiser to northern Minnesota (Bemidji) for the summer and will return in mid August. I figure about ~2,500 miles by the time she is back (with driving while there). No off-roading, no really rough roads, and I've instructed her to avoid turning the wheels when possible ;)).

But, if the consensus here is that it would be an act of poor parenting to let her leave 'as is' I guess I could take Monday and Tuesday off next week b/4 she leaves Wednesday and try to get this done. I'd be stuck buying parts from my dealer as I couldn't get them from CDan in time. Likewise I'd be without the front axle service DVD and I'd need to find a 54mm hub socket pretty quick.

But, I already have the 100 series pads and new front rotors from CDan (isn't that the most expensive of the parts?). I could also probably talk my way back into the shop and use the lift again (plus they have a hot water parts washer to clean up everything).

I better stop talking or I may talk myself into doing this and I'm really hoping to wait until a few other St. Louis mudders are ready so I can make it a group thing.

I'll wait and see what others say - thanks for the advice so far!
 
Jeez, I was hoping for good news. Or at least news that the cruiser's two month (~2,500 miles) trip north for the summer would be no reason to worry and I could wait until late summer / early fall when I have more time.

No clicking of any kind. Does that change your diagnosis?
Oh, I'm pretty darned sure you can go 2,500 miles, especially if they aren't clicking. Just don't think that because they aren't clicking you can put it on 38" tires and go reversing uphill turning with the front locked ;)

Birfs are pretty tough, but that grease looks like the color of "birf soup" to me, which means that seals have probably been failed for at least a little while.

Don't let it sit and fester and keep putting it off... get to it after your trip :beer:
 
I'm in the middle of doing mine. It's my second knuckle job (did my 62 last year) and much easier the second time around. You definitely need the 54mm socket, a seal puller, and some brass drifts in addition to the normal tools.

The DVD does make it much easier. I would have been leary to do it w/o the DVD or having someone around that has done it before. If you are going to rip into it I would plan on it being a 3-day process if it is your first time. Pretty much a full day to disassemble, a day of cleaning, and a day to put it all back together. Yes, there are people that can do it all in a day :flipoff2:.
 
since switching to 100 pads now requires new rotors
Didn't know that..., not sure why that is. I've had my 100 series pads on for 25k or so, with stock rotors. No problems here. Maybe I should change the rotors out in another 30 or 40k when it's time for new pads.

I'm not for sure that qualifies as a seal failure. Wish I still had pictures of mine around, to show what it looks like when the axle seal goes. The front of the DS side looks a "little" soupy, but I bet most of that others is just 10 years of wiper buildup. Just plan on doing the job but keep and eye on it in the mean time, no reason to panic here.

:beer:
Rookie2
 
3-days seems like about what I expected, and there is really no way I can get this done before this coming Wednesday when the truck heads to Northern Minnesota for the summer.

Sooooo, my plan is to wipe the back of the knuckle and clean it up as much as I can without using the pressure washer so as not to force water into the hub and further contaminate the grease.

However, is there anyone that thinks it is LIKELY that I will have some sort of front axle failure during the next 2500 miles if I put this off until the cruiser is back home? I know 'anything can happen' but I'm hoping for better advice than that - and I'm not expecting a fortune teller.

Should I bother trying to add grease through the square nut in the top of the knuckle?

Thanks all!
 
Should I bother trying to add grease through the square nut in the top of the knuckle?

YES! Lubrication is a good thing down there...
 
Didn't know that..., not sure why that is. I've had my 100 series pads on for 25k or so, with stock rotors. No problems here. Maybe I should change the rotors out in another 30 or 40k when it's time for new pads.

I'm not for sure that qualifies as a seal failure. Wish I still had pictures of mine around, to show what it looks like when the axle seal goes. The front of the DS side looks a "little" soupy, but I bet most of that others is just 10 years of wiper buildup. Just plan on doing the job but keep and eye on it in the mean time, no reason to panic here.

:beer:
Rookie2

Thanks Rookie that's just what I was hoping for.

FWIW, the new rotor with 100 pads came from CDan - I don't know exactly why as I don't question Dan's advice on parts. However, I believe he said something about the 100 pads being bigger than the 80 pads so the wear on the rotor wold be different and the 100 pads would be riding on the outer edges only (very bad braking). Turning the rotors would solve this but seems people on mud and Dan do not recommend turning 80 rotors. If you've had em on for that long, I'm guessing they are well bedded in and you're fine.

As for the axle, I really have to stress that nothing looked 'soupy' when I started. The only reason anything ended up 'soupy' was my abundant overspray of PB blaster on the brake lines and later dripped brake fluid from changing the lines (can't remember exactly when I took the photos). But when I first looked at the knuckles, there was a TON of crud built up but it was pretty much all dry and hard to remove except where the wipers sweep while turning and that I was able to wipe off with a rag and it seemed like just excess grease (which is the point).

Thanks again for the advice. I'll clean everything up 'lightly' and watch it the next few days.
 
YES! Lubrication is a good thing down there...

Any suggestions on what type of grease to use given that I don't know what is in there now? Is there a standard that my dealer would have likely used, or does it really matter if I mix grease given that it will all be changed out in about 2,500 miles?

Finally, what is the exact procedure for adding via the square nut?
 
FWIW, the new rotor with 100 pads came from CDan - I don't know exactly why as I don't question Dan's advice on parts. However, I believe he said something about the 100 pads being bigger than the 80 pads so the wear on the rotor wold be different and the 100 pads would be riding on the outer edges only (very bad braking). Turning the rotors would solve this but seems people on mud and Dan do not recommend turning 80 rotors. If you've had em on for that long, I'm guessing they are well bedded in and you're fine.

Yes, it should be pointed out that the 100 pads are bigger than the 80's. there's one small area on the front edge of the pad and one on the back, that doesn't contact the braking surface of the stock rotor, so when you start to get some wear on them, a unwarn lip will develop in these to areas (not anywhere near as big as the picture you had above). After a couple of thousand miles on them, once this unwarn area is clearly identifiable, I pulled the pads back off and cut out these two areas down to the plate with a dremel and cutting wheel (no biggy) ... so now 100% of the pad wears on the rotors.

As far as adding grease, you can go to autazone and get a tube of coastal greese for cheap and add it through the square plug. Check the level with a straw or something similar, you should be able to get an idea of how much is in there. DON"T overfill it. I made that mistake when I first bought my rig. Packed if full and a month or so later I had puking birfs.

:beer:
Rookie2
 
Your axle seal is blown out so you probably have thick liquid in the knuckle rather than grease. If it were me I would just fill the knuckle with grease, leave the gunk on the outside until you are ready to rip into the job, and top off your front diff. which is probably low from the axle seal failure.

On mine the good side was full of grease. The side with the bad seal had the "birf. soup". It ended up being way easier to clean the birfield since the grease was broken down by the gear oil.
 
Today I noticed a funny puddle under my driver side front wheel.
She's been standing for a week now.

A feel and a smell and yep, it's birfield soup.

As my other truck is on a road trip, I'll fondle with my front axle next week.

Cheers
birf1.gif
birf2.gif
 
As far as adding grease, you can go to autazone and get a tube of coastal greese for cheap and add it through the square plug. Check the level with a straw or something similar, you should be able to get an idea of how much is in there. DON"T overfill it. I made that mistake when I first bought my rig. Packed if full and a month or so later I had puking birfs.

How full is too full? Did you just use a standard grease gun "zirk" head to squirt the grease in?
 
yup, I would clean it up, fill it up, and check in a few days to see what transpired... :)
 
Back
Top Bottom