signs of wear on my cam lobes

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Oct 27, 2003
Threads
490
Messages
9,928
Location
North Cadillac
since the cruiser is down, waiting for starter parts from Cdan, i figured i could go ahead and do some things i've been needing to do for a while. One being the valve cover gasket, plug tube seals, pcv grommet, ect...

I already had the parts on hand, just never got around to it.

I will attach a bunch of pictures of what i have found so far. Few things i've noticed is that about half my valve cover bolts were loose. Also, the intake is really dirty.

What concerns me is that when looking at the lobes on the cams, there is visibly signs of wear. I have not checked the clearances yet, i will in the morning. I wonder if this wear is normal? Here is a few pics of the lobes. I will try to get more tomorrow in daylight.
valve cover change 008 (Small).webp
valve cover change 009 (Small).webp
 
pictures of the filthy intake...:o

Do you think installing a PCV catchcan will eliminate this?
valve cover change 001 (Small).webp
valve cover change 003 (Small).webp
valve cover change 002 (Small).webp
 
pictures of the cams. Looks OK to me for a motor with 186,000 miles. Little grungy gunk.

Chain tensiioner appears fine also.
valve cover change 005 (Small).webp
valve cover change 006 (Small).webp
valve cover change 007 (Small).webp
 
Pictures of the underside of the valve cover. Notice some of the spark plug tubes seals where so brital they were allready broken apart. It appears some oil was down on the plugs. I guess that could be a reason it seemed to be running sluggish.
valve cover change 011 (Small).webp
valve cover change 014 (Small).webp
valve cover change 012 (Small).webp
 
Deja Vu....
http://flickr.com/photos/nate-weibley/sets/72157594422127283/

I found everything exactly as you found it... rear cover bolts loose, some plugs with oil on them, filthy intake, etc. To a tee, everything was identical.


Interestingly you engine seems alot less "orange" then mine... I wonder what gives?
 
concrete,

That looks exceptinally good for 186K on the cam and head. Just keep your valves adjusted and if there are no deep gouges on the lobes, you look ok. From what I can see, deposits on the head are not baked on indicating alot of heat. Overall I think very good. Intake will always need pm and be dirty no matter what filter you use. If you want it pristine, tear into it every 30k to clean it. Looks overall good for 186k. What oil/filter and air filters are you using?
 
concrete,

What oil/filter and air filters are you using?

I've owned the truck since 110,000. Since then i've run either toyota or napa gold oil filters. I've always run M1 oil. I also have a k&n air filter :o ....i plan on changing back to a stock filter.
 
Crete,

M1 will help keep your motor CLEAN. First hand here. I tore into my Trooper for the first time w/ a mitsubishi mechanic friend of mine at 145,000 to do the valves (weekend work at the dealership). The Trooper is a VERY bullet proof and capable vehicle with the only downside that it tends to burn exhaust valves with the 2.6/4 banger in the model I have. Very heat sensitive like the FZ. I love it though. 20 mpg if you baby it and 7 skid plates on my limited model....

My mechanic friend was amazed at how clean the motor was. At 145K, there was NO deposits related to oil at all....absolutely none. I broke it in w/ dino for the first 6K and have fed it M1 since. There was barely any bottom or top end wear....Yours looks darn good to me. I use M1 in every vehicle from my wifes Buick Park Avenue to the Chebby and Toy and always will...

Is it the first time you have been in it?
 
i'm thinking i should keep digging and take the intake off so i can really clean it. What say you? How much more from here do i have?
 

vs
attachment.php


Seriously... what gives? I use M1 0w40 too... should there be that much variance in color?
 
The toy has fuel injectors so it will be dirty below where you have disassembled it to the combustion chamber area where the injectors start their business... The good thing (relative) about my chebby and trooper is the throttle body injection. There is a glorified carburator on top of those motors, but it is very easy to keep clean... I have never had problems with the throttle body injection...Every thing stays clean below the injectors...Especially w the redline I run to keep everything clean and the o2 sensors performing...

I have never had to replace o2 sensors in the chebby or trooper. The redline actually stopped the annoying code 28 I was getting on the Toy right after I got it 3 years ago. I had to pull the EFI fuse after every time I drove it to reset it...aggravating. Never a code 25, 26, or 28 after the second tank (full bottles) and the reccomended amount in fuel going forward after that.

Last time I had the Toy apart, I cleaned my throttle body but did not go below that. What I did after I got it back together was remove the air filter, ran the truck, and shot carb cleaner into the intake with the engine revved up to 2k so that it would stumble some, but not cut off....It may have cleaned some of the deposits below that but I do not know since I have not had to tear into it that far. It has not hurt my MAF either (so far).
 
When I got at some of the carbon deposits on my intake with a rag they were very very very stubborn. I doubt anything through the TB could clean it thoroughly. The whole intake would have to be removed and painstakingly cleaned. I'm not sure exactly how worth it doing so would be, but so far I'm 2/2 seeing black intakes during a valve cover gasket job.
 
Brassfield.......
thats too funny, concretes former rig was the 2.6 trooper, the start of the wheelin craze. and he used to work for wilderness systems pouring boats, not dagger but close. where you at in NC?
 
i'm thinking i should keep digging and take the intake off so i can really clean it. What say you? How much more from here do i have?

Concrete,

I think the cams look OK. Mine was all discolored as well. I think most of that is heat related. If you're using M1, you likely did not cause that discoloration. Most likely PO wasn't as anal about it.

Intake also looks a lot like mine did. I removed it, which means pulling the engine harness that comes over from the USPS firewall.

This is 2-4 hours, depending on banana status.

I took the head and both intake halves to a machine shop for a bath, shave, and valve job. I first cleaned out the top EGR port, it was completely plugged on mine.

If you take the head out to be serviced ( I highly recommend this) be sure to remind them to catalogue the pucs. They need to go back in the exact same spots they came out of).

Sending the injectors to RC Engineering will run you $184, and is well worth the time and expense. It just makes good sense to do all you can while you have access to everything. I have a shipping box with padding I can send you if you will pass it on when you get done with it.

This is also a great time to install a better power steering fluid cooler. Buy a kit, or source a used tranny cooler from a salvage yard.

Be sure you do the other recommended PM stuff while you are at it.
Fuel filter (have to take it off to take intake system apart)
Starter contacts (30 minutes on the bench)
Alternator brush pack (15 min on the becnch, if you are slow)
Clean the EGR pipe
Belts
ALL hoses
PHH included
service or mod fan clutch
flush radiator, have it leak tested ($15 at a radiator shop)
Dist cap, rotor, wires
plugs
Water pump
Thermostat, housing orings
Exhaust manifold rings, gaskets (come with head set fm CDan)
Oil pump cover bolt mod (you are right there)
Acelerator cable if yours is as ugly as some get (easy access)
Steering shaft firewall gromet, if needed (easy access)

DO NOT worry about the lower end. At 225k, mine showed no signs of wear, and still had the factory cross hatching on the cylinder walls.

I'm still down due to two different shops screwing up the block, in different ways.

I also took the time to:
Bleach out my overflow bottle, now it is clean as new.
De-gunk as much of the under the engine stuff as possible
Clean the center console pf all the crap that gets around the base
Clean the carpet nearby
Clean the boots, shifters
Remove all the crappy old fake wood.

Almost forgot, be sure to get new head bolts from CDan.

HTH,

Dan
 
Last edited:
Dan, you are trying to push me over that slippery slope!!:flipoff2:

What really sucks is that i'm tight on money right now and all the things i really would like to do, i can't. I am fixing what i have parts for allready.
 
Dan, you are trying to push me over that slippery slope!!:flipoff2:

What really sucks is that i'm tight on money right now and all the things i really would like to do, i can't. I am fixing what i have parts for allready.

That's cool, I'm just sayin....
 
you'll regret it if you don't.

go find some cash, say another $500.00.

you'll be glad you did..
 
Brassfield.......
thats too funny, concretes former rig was the 2.6 trooper, the start of the wheelin craze. and he used to work for wilderness systems pouring boats, not dagger but close. where you at in NC?

I am located in Goldsboro, 45 minutes east of Raleigh...You must be somewhere around Winston? I paddle whitewater quite often out that way...
 
IMHO your engine looks very good for the mileage. I would clean up what is easy to reach, check the valve clearances, doing the injectors is probably a good investment at your mileage, then put it together with new seals/gaskets and drive.:cheers:
 
Back
Top Bottom