Thoughts on Power Pack from MAF

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Shinichi,
I drove past that Cruiser for a little over a year and was thinking about stopping and trying to buy it. What did you end up getting it for? Down the road a bit is a FJ55 sitting in a yard, probably cheap. I have met John, I used to go to the 4wheelers 4x4 club meetings. I met him there, that rig is cool. The Proffitts cruiser dudes looked at an 82 FJ40 that I was selling on Ebay, they also build some sick rigs. Have you seen the HJ47 sitting in Carbondale in pieces?
 
I think being able to not misfire at 350 rpm is more important than being able to get to 9k. But on the same note, it sounds like a quality upgrade. If I was to change to 3fe intake and ignition, would the money be wasted on the DUI, or would it still be fuctional for that setup. A 3fe is electronic from the factory right?

Alpendubber, I paid $1000 for it. The body is not too bad, and everything works. I been driving it for the last two months before I took the springs off. Including a trip to the mill at Crystal above Marble. You can't discount the durability of a land cruiser.
I have seen that 55 sitting in the grass. John at Proffitts said the it was for sale once, but the price was not realistic. Did you notice the white 60 just down the same road. The workshop it was next to burnt down last week and cooked that truck with it. They were going to take it to the dump, I took it to Proffitts (saved me some money on the springs). Those guys are going to use the some of the drivetrain, but the body was a total loss. I didn't keep it because I don't have a place to put extra cars. Townhomes don't like burnt up cars sitting around. Long story short if you have space where you live, I will keep you in mind next time one comes up. There are a lot of 60s in the valley, and they seem to come up cheap every once in awhile.
 
lcwizard said:
don't know how jim calls the DUI dist cheap.
The GM design brief called for the most inexpensive electronic ignition system that could be brought to market. That meant eliminating the coil wire (to eliminate expense) shrinking the coil to fit inside the cap (to reduce expense) putting the pickup & amplifier electronics inside the dissy (to reduce expense) using a stamped advance mechanism (to reduce expense)...

But the most brilliant piece of the original HEI system was, after the cost accountants finished "designing" the ignition, the marketing department called it High Energy Ignition. I love that!

They are also literally cheap, $98 @ advance auto.

The GM HEI still holds it's place amoung the performance people as the best OEM ignition ever built. Which is why companies go to the trouble of fitting them to Ford, Dodge, Toyota , AMC , Rover, Jeep and others. Toyota ignitions will never gain that honor.
I would disagree with that. Much like the VW type 1 or the SBC engine, due to the extremely low cost and ready availability, it has become the choice of budget conscious hot-rodders (that's 98% of us).

I bought a 78 new, and in 1980 I installed HEI from K& L (long retired) the stock ignition couldn't hold a candle to it when it came to low end pulling. To it's favor ,the stock ignition was fully waterproof ,howver i don't ever remember drowning out an HEI.
A statistical sample of 1, while an interesting datapoint, is not exactly a trend. The '78 dissy had vacuum retard (a bad thing). It is still a good dissy, but needs to be adjusted slightly to work to it's full potential.
 
the HEI is only cheap for stock applications. When you machine a new body to fit the ford, dodge, rover, toyota or all the other applications, it becomes more expensive.
Despite that, it carries enough following that non GM owners are willing to pay for the "upgrade".
Tried recurving the stock at a phoenix distributor shop, not much improvement,
certainly not up to the hei performance.
Not to mention don't have to worry about the ignition module, which last one i replaced, cost nearly as much as the Landcruiser HEI unit and was not available at the local auto parts store.
All the replacement parts for the HEI can be got at any parts store in america, with the exception of the Land Cruiser specific parts, the body and gear
 
According to MAF the DUI isn't cheap, they want almost five bills with the new wires. Jim, what does a recurve cost and an altitude adjustment on my carb too. I live at 6 or 7 thousand feet, and go up from there.
For the cat replacement, does the tubing have to be anything special? Would it be easier to skip the flanges? I am learning to weld, and exhuast seems to be a good place to hide a new welders welds.
Oh, and a word of advice, full length clothes are a must. I thought it was a recomendation to protect from splatter, not so. I burt the sh*t out of my legs practicing on lawn mower blades. The worst sun burn (UV I guess) I have ever had. go ahead and laugh, it was pretty stupid on my part:doh:
 
Hi all,
I wrote this mail below to Man a fre and afrer reding some feed-backs it made me worried, so if you would like to help me to? is it better just to buy a original Carburator NEW or a WEBBER? etc?

My Name is Andre de Zeeuw and I live in Indonesia, I am extremely interested in the FJ40POWERPACKC 1/79-1983 FJ40 Performance Kit; Please advice the information you need from me to find-out exactly what year my FJ40 - 2F Engine is the car is from 1978 but I think the Engine is from 1981, I could give you the imprinted numbers on the Cylinder-head etcetera? Definitely I do not need to worry about fuel efficiencies, etc I only need a lot more power, when I racing I always get second (3x already) out of 40 cars….. I want to be first and beat the fastest TURBO on the Island, ha ha. The good thing is I always beat the other turbo cars with my 2F stock engine…..

1. The 1968-9/1973 USD 1,650.00
2. The 1974-12/1978USD 1,705.00
3. The 1/1979-1983 USD 1,565.00

I do need to worry about the following;

1. My car is for serious mud-bogging, so do you have a good suggestion on CARB & Cables so the water does not go inside, now I seal everything with a lot of Silicon.

2. Do you have a book to maintain/adjust the WEBBER and also for the 2F engine like HAYNES?

3. Now my ignition system is “”Magnetic High Energy Electronic Ignition Porter”” from Canada this has a separate coil attached and the original ignition distributor is still in place, just the inside is striped of the platinum and replaced with the Canada part, not a perfect solution, on your system there is no separate Coil as on the picture attached?

6. I do need a super good guidance for installation as I am just a normal mechanic, nothing special.

7. Do I need spare-parts for this installation? Or does the ignition distributor not wear down or break?

Many thanks,
Andre de Zeeuw
 
Back
Top Bottom