So here is a short video of us wheeling to our camp site in Southern Arizona with the M416 and my new trailer mods
m416 trailer lid rack and water cooler holder Land Cruiser FJ 80 custom builds - YouTube
I have a 97 Cruiser and want to know if the alternator is an "internally regulated" Nippondenso with remote sense? if so, the instructions for installing isolators requires a fused lead from the ignition wire to the E post on the Isolator.
thank you very much for the help
scott
wheel bearing preload
from my personal experience of doing 25+ front hub rebuilds on diff 4x4's and on my 97 Cruiser which i've installed 4.88's 3 yrs ago and have done the front hubs 4 times now i say follow the manual exactly unlike I did.
Once was to just lube them after the ring/pinion...
I went to the Gap twice this week and there is a construction crew with a D-6 dozer, back hoe, and a huge track hoe hired to take all the rocks out and make the trail easy for a regular 4x4 to access it. i have searched for info about this and cant find anything about it.
if you want to...
I just connected a Hopkins/Hoppy 48845 wiring harness at the end of the old wires that were already on the hitch. I never tested the wires before now.
After splicing the 5wire Hoppy to my 4flat, i still have no power. I dont' even have power at any of the wires coming over the truck using a...
thanks for the replies but I dont have any power at the end of the plug before even connecting to the trailer. I will resend a new post since I dont think I did this one well enough and i haven't done many and this is driving me nuts not being able to get power
thanks all
still need help iwth wiring harnes
I installed a Hoppy 48845 and at the end of the new 4 wires that come out, i still have no power out when trying tail, brake, or turn.
does anyone have any ideas on why I still can't get power?
thanks a lot
Scott
I am trying to wire a trailer wiring harness at my rear bumper and I can't get any power through any of the existing wires.
the old outlet on the truck is gone so all if have is the loose wires
any help is much appreciated. i have wired a lot of chevy trucks in the past and this is my first...
i love my 4.88's with 35", (yes, 4.10's stock)it's a little lower geared than stock. the best i got was 16 but that's as light as you can possibly get on the throttle around town. that was also with 135k miles on the exhaust/both cats/muffler, and the rear canister. i now have 21/2" and a...
Fred, thanks a lot for the ideas. I actually didn't see the bleeder on the lspv. the brake pedal was not this spongy/soft before the new brakes. i have bled them since the new brakes and I didn't see any bubbles come out at all. I'll redo them per your suggestion again! thx
I can't believe...
mostly charouleau gap...yesterday was great. just to the saddle and back is what i usually do.chiva falls if i get across town. we're going this saturday if u want to join us
Thanks Fred,
I did not adjust the rear lspv in the rear after the install hoping for more front brake power for the down hill part of wheeling. my brakes dont work very well though. i have redone ft/rr and sometimes if i'm in low/1st going down a steep decline, I can barely hold...
Hello, I am replacing my exhaust and I need two new weld on flanges so I can bolt up two new O2 sensors.
Does anyone know where I can purchase these? Toyota says I can and no exhaust places in Tucson,AZ say they can get them either.
Thank you very much in advance...hopefully cruiser Dan is...
coil springs have a linear spring rate..therefore compressed 2 " from static ride height or 4 " the spring rate is still the same.
why would hot or cold make a difference except possibly in longevity of the steel?
thanks