Search results for query: *

Forum search Google search

  1. K

    Spicer 1310 rear driveshaft flange P/N?

    Does anyone know what the spicer 1310 ujoint rear driveshaft flange p/n is? rear at the diff end. thanks. Kyle
  2. K

    Nice 80 Series on E-Bay - Price Check

    way too much. especially with no known history.
  3. K

    Rear Diff noise w/vid

    will get them later tonight. the amount of goo was not excessive, it was there though. I assume it is mainly from the gears re-seating.
  4. K

    Rear Diff noise w/vid

    pulled it apart. Oil was Mobil 1 75/90 LS Synthetic. A big mound of black "metallic" goo stuck to the magnet. Drained (most of) the fluid through a paper towel and quite a bit more of the goo was in the oil, as well as in the housing. No abnormal wear on the shaft splines. No abnormal wear...
  5. K

    Rear Diff noise w/vid

    new (different) pinion flange. Crush spacer the first time. would have to swap the pumpkins. the housing is welded upon quite heavily. Will snap some pics when I can pull it apart. Hopefully this week one evening.
  6. K

    Rear Diff noise w/vid

    yes, no dif cover on a 80 rear axle. (or front for that matter)
  7. K

    Rear Diff noise w/vid

    yeah I'm thinking a spun bearing... going to pull it out hopefully this weekend...
  8. K

    Rear Diff noise w/vid

    96-97 fzj80 open rear diff. (not on an 80 though) Before I ever drove it, Had diff rebuilt by shop 1, they screwed up the crush sleeve and basically trashed the gears. became noisey really fast. more of a whine then became a rattle. gears were worn to a knife edge. approx 250 miles later had...
  9. K

    Trail-Gear is babysitting my rig!!

    according to a thread on PBB, they are jumping into 80's and land use awareness.
  10. K

    Toy rear 8" Auburn LSD up front?

    Can you run a rear 8" auburn in the front of an 80? (i know it bolts in, but will it work, or do you have to swap the side gears like in a truetrack, or is it a complete no go?)
  11. K

    DIY pinion bearings?

    My D2 axle swap thread - Pirate4x4.Com Bulletin Board redition 1 and 2 as i redid the front 3link
  12. K

    DIY pinion bearings?

    cool.
  13. K

    DIY pinion bearings?

    Do you have to re-shim when replacing pinion bearings? (OEM toyota ones with a new crush sleeve) maybe a dumb question but i have never dealt with toy diffs before...
  14. K

    Who sells built rear diffs?

    pinion bearings are kinda wobbly. it looks like the r&p has some wear from it. not bad, but i dont want to rebuild it with a bad gearset... supposedly had less than 80k on it before, so i dont know... how much you think you want for that open third?
  15. K

    Who sells built rear diffs?

    I have seen a few rear built diffs, but none with OEM 4.10's. am I missing someone? I am currently open, but a rear e-ocked third new might be an option unless there are more choices.... I fried the rear (i think the pinion bearings gernaded) and really dont trust rebuilding it with the RP...
  16. K

    installed a oil seperator on my 80

    shouldnt the PCV vent be pre supercharger on the vacuum side of the intake air track? otherwise it is seeing positive pressure and not venting like it should right?
  17. K

    Left thread TRE p/n?

    thanks for the replies. got the info from Jacque at Toy of Dallas. Lightning fast too.... Kinda in a bind, but mainly because of poor planning on my part... and apparently according to toy FW, land cruisers between 94-97 are completely different looking trucks..... Thanks kurt, will keep you in...
  18. K

    Left thread TRE p/n?

    Need a Left thread TRE (23mm) does anyone have the p/n? Thanks, Kyle
  19. K

    diff flange interchangable?

    will a toy 8" front diff flange fit a rear diff? (96 LC, the splines, not the driveshaft bolt pattern)
  20. K

    TLC Lamp Guards like Rovers in web site below?

    those are made for the old rovers that had glass lenses.
Back
Top Bottom