Search results for query: *

Forum search Google search

  1. hward1

    carb likes to stick

    doing this sticking thing again -- started after a trip where i guess holding the pedal down in the same postion for awhile -- wonder if one of the springs are to strong enough to bring it back like it should
  2. hward1

    Want to see a $89,000 FJ62?

    i would have at least replaced the brake master before asking that much ha
  3. hward1

    Timing cover bolt leaking

    pan -- georg @ valley hybrids gave me advice some time ago on how to replace the pan gasket oem // get some copper spray spray the gasket put about 4 coats on it both sides / spray the block after cleaning ALL of the old seal off ect. (dont spray until you are ready to install the gasket) / put...
  4. hward1

    60 Frame Rust - what to do

    do you have to remove the gas tank to replace the rear side channels if you plan to grind the rivets out --
  5. hward1

    fj60 squeaky clutch pedal

    finally got the squeaky clutch fixed -- my clutch master cylinder was a aftermarket type - previous owner had it replaced at Alert transmission and brakes in Knoxville for crazy $396.44 and they didnt even replace the slave at the same time and 2 months later they charged $338.57 to replace the...
  6. hward1

    Axle seals - Remove knuckle housing?

    or rent it at autozone for free if you got one
  7. hward1

    Here I go...removing the head

    the T the small side turns back towards you after removing the hose - maybe 17mm but not sure -- maybe 19mm for then removing the larger part that goes into the head - shouldnt be to hard to turn - great time to replace the two hoses - also when putting them back in a type of pipe liquid seal is...
  8. hward1

    ome lift now have vibration (didnt before)

    ok thanks georg -- will be looking out for one - thanks again for your help --
  9. hward1

    ome lift now have vibration (didnt before)

    yesterday and today got the 4 degree shims installed for the front and rear -- the vehicle no longer wonders all over the road and the vibrations are gone in 2wd -- i also purchased a new ome rear A spring and installed that - so i now have two A rear springs instead of the A and B -- so...
  10. hward1

    ome lift now have vibration (didnt before)

    small update: added the front larger tires with 1.5" wheel spacers and noticed the vibs changed some (got worse) small vibs up to 25mph more noticed at 25mph before same vibs with the small tires with this setup the vibs were only at the 25 mph range well tried something after...
  11. hward1

    ome lift now have vibration (didnt before)

    ok thanks georg -- will call soon for another shim - raining today as usual around these neck of the woods
  12. hward1

    How to extend the rear breather hose for a ome lift

    extended the rear breather hose with 2ft cut napa fuel line hose and reused the valve on top - fast and easy
  13. hward1

    FJ60: Transfer case rear output seal

    got my kit from georg - great guy and willing to help if you have any problems along the way
  14. hward1

    FJ60 Tachometer Repair

    my speedo bounced around a little - another one fixed the problem
  15. hward1

    Front Leaf Spring Question

    best way just place them standing arch up and which ever is higher goes on front drivers side - ome has printed paint model # + or - or 0 rear with model # with both A or both B or A and a B if its not worn off rear if different A goes on passenger rear - B on drivers rear
  16. hward1

    ome lift now have vibration (didnt before)

    - that amazon angle finder looks like a good one for the price yeah the lift is used --- or most of it is
  17. hward1

    Front Leaf Spring Question

    if its OME A is on drivers side
  18. hward1

    what degree shims did you use with your ome 2/3 lift kit

    anyone added rear shims to change the pinion angle
  19. hward1

    Good and Bad vendors and shop

    great idea to have something like this somewhere -- to many mistakes are time consuming for everyone but it feels better with someone with a great attitude -- i like going with someone that cares and has a great attitude -- for me its not always the price
  20. hward1

    Oil pan cap leak

    i purchased a oem one and it leaked at torque spec - added more torque like i would have before looking at specs and it stopped dripping - may help - next time im going to inspec mine for that nick
Back
Top Bottom