Search results for query: *

Forum search Google search

  1. Micah

    Need some help pricing to sell...

    Thanks, this afternoon I'll get more pictures.
  2. Micah

    Need some help pricing to sell...

    I have posted this in the classified section also. I know this forum has more traffic though.
  3. Micah

    Need some help pricing to sell...

    Yeah I think its that time... my wife needs a new car and I've got two cruisers and one needs to go. Unfortunately that means its the 62. Let me give yall a quick run down it. 1989 fj62 250,000ish miles Bundle of Snakes headers Runs great just not ran regularly (unfortunately it sits at my...
  4. Micah

    Cleaned MAF & won't run now

    Well the connector is hooked up and i have checked the vacuum lines as well. As for the two screws of death I did unscrew them, broke loose the gasket thing then saw what I didn't understand so I put it back together. I guess that was a bad thing...?
  5. Micah

    Cleaned MAF & won't run now

    Hey got a question... I went to clean my cruiser up and cleaned the MAF throttle body and put it all back together changed the air cleaner and now it turns over, run for a second or two idles up to 1000RPM then it dies. I need help, what do I need to check now?
  6. Micah

    trottle cable

    Yes fraying!! Sorry this all happened the day before I got married and I probably don't have to say that it was quite stressful. Does anyone know if the throttle cable from a FJ80 fits a FJ62?
  7. Micah

    trottle cable

    I search and couldn't find anything on this... where can i get a new throttle cable. I check my sources already and couldn't find anything. It is frying where it goes in through the fire wall. Thanks in advance!
  8. Micah

    Texas Junkyards

    There is a Land Cruiser Junk yard in New Braunfels TX called Wimberly Four Wheel Drive Here is address 7820 North Ih 35 New Braunfels, TX 78130-7124 (830) 626-3111
  9. Micah

    Best Mods under $50...

    i agree probably the BEST under $50 mod out there!!!
  10. Micah

    Newbie wondering a few things.

    Search for Rodney flush. It is a passive flush. I did it with my trans and it help a good deal.
  11. Micah

    FJ62 Tcase Rebuild 1st Attempt

    I also removed mine with out a gear puller. Except for the transfer input gear.
  12. Micah

    Broke this changing Alt on my 62

    I would post up in the wanted section. When mine broke I found a used one from a guy that desmogged.
  13. Micah

    staked nut and tcase flange removal

    Try using some heat, two summers ago when I rebuilt mine xfer case i took all day fighting with it then put heat on it to the point where it was smoking and it finally broke loose. I tried heat before but never got it hot enough. You really have to let it start smoking.
  14. Micah

    New Console

    It is the same quadratech console this thread is about. The drawer is not really a drawer but more of a swing out pen holder. But most normal pens are to long for fit. But you can still use it.
  15. Micah

    New Console

    Just realized that I never posted a picture of mine installed, sorry about the wait Here is a picture of the light switches that I have added to mine in place the the coin change holders
  16. Micah

    1989 fj62 fsm

    I have one if you were needing some quick pictures or pages out of one while you wait for yours to show up. Just let me know. Micah
  17. Micah

    Door Panels

    I used 1/8 inch ply wood for mine. Very cheap and turns out nice, especially if you take more time to sand then I did.
  18. Micah

    welding a rig

    When I cut my quarter panels on the passenger side all I did was put a damp cloth in between the weld area and the fuel lines.
  19. Micah

    welding a rig

    Yeah I usually ground to the frame. Is it true that you should disconnect the battery when grounding to the frame? Can't remember where I heard this from and can't remember the reasoning behind it either but I always do.
Back
Top Bottom