Search results for query: *

Forum search Google search

  1. heydanno

    2002+ window switch on 2000 Land Cruiser?

    @Jeremy9A thanks (4 months later!) much for your helpful reply. This saga is finally over. I ended up moving the wiring harness and window motor from the 2000 door to the replacement door, and I finally have a working window. And an installed door card after living with a bare interior door...
  2. heydanno

    2002+ window switch on 2000 Land Cruiser?

    Resurrecting this thread! Thanks to awesomeissquid and comparing to a more recent FSM the whole window signaling system is totally different. Not just a matter of a different switch connector. I am finally back to working on this project. I'm swapping the motor and in-door wiring from the old...
  3. heydanno

    2002+ window switch on 2000 Land Cruiser?

    Amazing. Thanks awesomeissquid ! I will see what I can come up with.
  4. heydanno

    2002+ window switch on 2000 Land Cruiser?

    Any electrical whizzes out there? Maybe someone with a wiring diagram for the 2000? (Assuming the 2004 from the FSM is the same as for the 2002 door.)
  5. heydanno

    2002+ window switch on 2000 Land Cruiser?

    I recently replaced my right rear door on my 2000 100 Series as it had body damage. The replacement door is from a 2002(?) Cruiser. Both wire looms plugged in perfectly at the door hinge. The speaker in the new door works, as does the courtesy light and the power lock. The problem is the window...
  6. heydanno

    Brake booster pump strikes again

    @OverlandOutdoors, did you replace the full MC unit yet? All is well? I've got the same sound as in your video, only on initial startup in the morning and only once in a while on my 2000 LC. After lots of searching on here I was going to just do the motor/pump/accumulator but after seeing your...
  7. heydanno

    Screeching/chirping (crickets?) at 1200 RPM

    Thanks everyone. As suspected, it was the serp tensioner. I installed the new one (following these directions) and the chirp is gone. However, I managed to cause a small, temporary antifreeze leak in the process and about a teaspoon of antifreeze dripped on the timing belt during the time the...
  8. heydanno

    RTH: Serp belt tensioner replace; antifreeze leaked onto timing belt

    I'm in the midst of replacing my serpentine belt tensioner today to fix a chirp/squealing noise on my 2000 UZJ100 with ~191 k miles.. Upon removing the tensioner (I followed these instructions) I notice a dripping from below the truck... ugh, antifreeze. Then I notice it is also dripping onto...
  9. heydanno

    Screeching/chirping (crickets?) at 1200 RPM

    Thanks for the suggestions, everyone. I tapped around the cats and I don't think the shields are loose. I didn't have much time this evening but I was able to get the noise to occur intermittently when revving the engine in the driveway (so I don't think it's wheel bearings), and it does seem to...
  10. heydanno

    Screeching/chirping (crickets?) at 1200 RPM

    Hi folks, Noticed recently on my 2000 UZJ100 with 190k a screeching/chirping/crickets/cicada like sound coming from the truck when driving around town. It happens around 1200-1500 RPM; if I goose throttle a bit or let off to get away from that range it goes away. My foot doesn't have to be on...
  11. heydanno

    Lumbar adjuster (Drivers seat) has stopped functioning

    Thought I'd resurrect this old thread with my experience. In my new to me 2000, the lumbar feels excessively firm so as to make it rather uncomfortable, but I couldn't get the motor to respond to release the support. This is how I fixed my problem: 1) First I checked the switch. I used the...
  12. heydanno

    What have you done to your 100 Series this week?

    Replaced heater hose T-fittings. Old ones:
  13. heydanno

    Apple compatible bluetooth dongle for ODB port?

    Thanks for asking this question, as I'm looking into the same thing. On a technical note, I believe that the only dongles that will work with an iPhone are those that use wifi and not Bluetooh.
  14. heydanno

    Trailer light wiring harness

    Have you made 100% sure it works at the trailer connector? Like, have you tested it at the plug with a 12 V power supply and gotten the correct lights to light up? A cheap multimeter will also tell you if you are getting the proper voltage on the truck side of things. Grounds can go bad real...
Back
Top Bottom