Search results for query: *

Forum search Google search

  1. Wadepat2

    Elate Supercharger install

    Nice progress!
  2. Wadepat2

    2uz engine build 300 to 400 to 500whp?

    Custom stainless long tube by Bullet Performance. 3" down pipes to large free flow muffler then 3" to stock resonator. Sounds like any stock V8 at idle and cruise speed with stock resonator. Over 3500 rpm it sounds like above. In cab it's not loud at all. I had 3" high flow res before and it was...
  3. Wadepat2

    2uz engine build 300 to 400 to 500whp?

    Finished off tuning with little offroad
  4. Wadepat2

    Emissions fail: high NOx getting higher?

    Just a guess from me but I would run regular octane fuel and stop the additives. Clean maf. Let it run a full tank without all the additives . Take a with a few hour long highway drives. OD off to keep rpms up to burn off anything in cats. A few hard pulls through the gears. Retest.
  5. Wadepat2

    2uz engine build 300 to 400 to 500whp?

    Luckily I don't drive as crazy as the build is. Daily driving isn't bad at all since still on stock size tires and manual trans. Using full boost .... yea it's bad 🤣
  6. Wadepat2

    2uz engine build 300 to 400 to 500whp?

    This thread has most of the performance upgrades. The one below is from the very start of the project. https://forum.ih8mud.com/threads/adding-sc-to-my-99-gcc-build-thread.1271240/
  7. Wadepat2

    2uz engine build 300 to 400 to 500whp?

    Yep that's mine
  8. Wadepat2

    2uz engine build 300 to 400 to 500whp?

    Project done. Will post full list from project start until now for anyone interested.
  9. Wadepat2

    2uz engine build 300 to 400 to 500whp?

    Yea those guys are crazy. Lots of turbo inline 6 cylinders here doing that. Not many supercharged v8s. They do love to hold it on revlimiter and shoot flames hahaha. Mine hits rev limit set at 6k pretty easy but I don't beat on mine. Only time it gets pushed really is on the dyno. It's just a...
  10. Wadepat2

    2uz engine build 300 to 400 to 500whp?

    Hahaha If it makes over 500whp I will try to keep it as it is. If it falls a little short I'll push it. Or I may get 500 then get bored in a few weeks and install it. Haha. It's just sitting there calling me to be installed and it was stupid expensive.
  11. Wadepat2

    2uz engine build 300 to 400 to 500whp?

    Boost numbers with stock crank pulley. 15psi at 3500 rpm and 17.5 at 6k Temps are good and no belt slip. Hope to have it on dyno in next few weeks once I get boost fueling dialed in. I'm not going to Install the ATI damper since it's 1/4" bigger in diameter and would put boost closer to 20 psi.
  12. Wadepat2

    2uz engine build 300 to 400 to 500whp?

    Yea 6 rib and extra idler to wrap belt with custom griptec pulley. Right now I'm not using extra idler and not getting any slip but I know it's coming once pushed. Once extra idler is sorted out looks like it will be good. At my max Ill be at the very bottom of what this blower can do. ~500 whp...
  13. Wadepat2

    2uz engine build 300 to 400 to 500whp?

    Making progress. Still working through a belt issue and waiting on Gates belt to arrive. 14psi at 3k rpm feels strong though :)
  14. Wadepat2

    2uz engine build 300 to 400 to 500whp?

    After a world tour from New Zealand to Australia to China and then to the Philippines my 1900s big brother Harrop 2650 finally arrived here in Dubai. Crazy how they are basically the same physical size with only about an inch difference in length. Install pending for next week. Any last minute...
  15. Wadepat2

    2uz engine build 300 to 400 to 500whp?

    For sure I can try to fill in a few things. No ABS, TRAC or VSC. Old school vac brakes work great..but doesn't really rain here so bad roads and rain or power loss could suck. Same as old school brake systems seen in US and even some newer models. I remember trying to stop my early 2000 F250...
  16. Wadepat2

    2uz engine build 300 to 400 to 500whp?

    I actually removed the Intake they built since it was aluminum and always crazy hot. This is just a 4" carbon fiber tube from Amazon and an Intake elbow. Other side under cover is 4" inlet cone filter. I did keep the filter cover but it doesn't do much. If I was in US I would try to find a CAI...
  17. Wadepat2

    2uz engine build 300 to 400 to 500whp?

    Eta for new Supercharger 3-4 days. Got engine bay cleaned up and ready for the install!
  18. Wadepat2

    2uz engine build 300 to 400 to 500whp?

    With the added hp needed to spin the much bigger SC I'm trying to give the small 6 rib belt some help. Typically 8 rib would be smallest belt used but not looking to lose the hyd fan and get further away from stock on accessories. Had Griptec do there grip process on my Elate 65mm pulley, adding...
  19. Wadepat2

    Elate Supercharger install

    Sounds like a great start. Look forward to your progress. I targeted the same lambda at that boost. I had Travis make me a 60mm manifold a year or so ago its been great even in crazy Dubai heat. Post up the pics when you get started. Feel free to message me of you need any specific pics are...
Back
Top Bottom