Search results for query: *

Forum search Google search

  1. roflbox

    Builds The Green Bastard

    Cup holder bracket is here: https://www.printables.com/model/740187-fzj80-cupholder-insert Still working on the others
  2. roflbox

    Builds The Green Bastard

    Which ones? :)
  3. roflbox

    Builds The Green Bastard

    Annnnnnnnnd we are back. Was able to find a pan on MUD, someone was swapping their transmission out, and agreed to swap pans with me. Installed it Saturday, and just filled it up today, will give it a look over tomorrow, and then drive it around a little bit. Hopefully I did a good enough...
  4. roflbox

    Builds The Green Bastard

    yeeeeeeeeeeeeeehaw turns out I have spun the bung for my transmission drain plug
  5. roflbox

    Builds The Green Bastard

    I have been keeping my 3d printer busy :D Going to be making a few versions of that bracket for the cup holder insert (most likely a heatset version that can be used for ram mounts), and then releasing the printable files for free :D Progress has started on making a ashtray bracket as well
  6. roflbox

    Builds The Green Bastard

    Yes
  7. roflbox

    Builds The Green Bastard

    passed inspection, just went to a different jiffylube this morning, and voila the jb weld didnt set, so I just took it off before going
  8. roflbox

    Builds The Green Bastard

    what a PITA inspections are. first place says "your taillights have to be red" 2nd place says "you have an exhaust leak, and blah blah blah that is part of safety, not emissions" I have globbed up the y pipe with JB weld hitemp, and will test the winds of fate tomorrow
  9. roflbox

    Builds The Green Bastard

    I went with a new distributor, and glad I did, when I pulled the old distributor, the PO had done some work to stop oil leaking by slathering the distributor with black gasket material, and the exterior of it was pretty caked with gray gasket material too. If I can find internal parts, I will...
  10. roflbox

    Builds The Green Bastard

    Big day today! Cruiser now runs again, new distributor was what fixed it. Snagged some spare rims for the cruiser from @White Sheep and saw the progress on both of his money pits And thanks to @fourtrax for the excellent walkthrough of the steps to replace!
  11. roflbox

    Builds The Green Bastard

    Tried again with the door cards, my program was a lot closer this time, but still things are out of wack / too tight, going to continue to tinker on that
  12. roflbox

    Builds The Green Bastard

    My new one should be here from partsouq on Jan 2, if I can get some replacement parts for the current one, I will keep it
  13. roflbox

    Builds The Green Bastard

    per the suggestion of the wise lumbee1 Opened up the distributor, and found that there has been moisture ingress:
  14. roflbox

    Builds The Green Bastard

    Alright, My code I can pull is a P0340. (Which I now learn is not what I replaced a part for :( ) Reading the FSM for the following codes: P0335: This test is to read resistance between pins 1 and 4 (Passes in range) (This was also a test to make sure my el-cheapo multimeter was working)...
  15. roflbox

    Builds The Green Bastard

    well, it was not the crank position sensor? back to square one, still pulling codes for the sensor though 🤔
  16. roflbox

    Builds The Green Bastard

    hohohohoho put a new AM1 fuse in (though I think this was unrelated, still nice to not have a fuse covered in green fuzzies) Cranked for about 15 seconds, and still no CEL, but kept the key on and was able to read a code for the camshaft sensor Going to double check the FSM, and then re-load...
  17. roflbox

    Builds The Green Bastard

    nothing yet, waiting for fuses still
  18. roflbox

    Builds The Green Bastard

    alrighty then. Some interesting tidbits: confirmed no CEL with key in "on" position. the "bad" fusible link still passes a continuity test (I kept the terminals apart on the battery hook up side. Looked at my AM1 fuse in the engine fusebox, and saw that it had some pretty prominent green...
  19. roflbox

    Builds The Green Bastard

    poop was driving last weekend, and things were fine, went to costco and filled up, went to take the LC out today, and have a crank no start. starting to dig in now, looks like the fusible link, and EFI fuse are ok, going to start digging around further snagged a inline spark tester, and a...
  20. roflbox

    Builds The Green Bastard

    Alright, took a new photo of the door panel. This time used my DSLR, put on a 50mm lens, stood on top of the workbench, and photographed the panel laying on the floor, just finishing up the sketches in fusion now, and might try making some cuts again this weekend?
Back
Top Bottom