Search results for query: *

  • Users: MisipLC
  • Content: Threads
  • Order by date

Forum search Google search

  1. MisipLC

    97 Crank and No Start

    I have a 1997 LX450. It began with a crank no start. Took the truck Toyota and they replaced the relay in kid panel on the driver side. The truck crank and ran. I brought it home and the truck continued to crank approximately for several days. Then it would not crank. I research and read...
  2. MisipLC

    Cylinders 5 and 6

    So, we have a misfire on cylinders 5 and 6. We changed injectors, checked for ECU signal, replaced plugs and still have misfire cylinders 5 and 6. Going to check for compression tomorrow. I have searched forum for ideas and have not found any ideas. Cylinders 1-4 are fine. Cylinders 5 and 6...
  3. MisipLC

    Engine Harness Wire Size

    Researched the threads and found no info. Looking for the size of wire used on the ground side of fuel injector plug. We have misfire on cylinders 5 and 6. Ohmed out injectors and they are good. Checked voltage on injector plug and no voltage. Put ground side of meter on manifold and positive...
  4. MisipLC

    A Happy ECU

    I have searched and looked with no luck answering my question. I am trying to figure out what it takes to make the ECU happy. In other words, what signals are required to make the ECU send the "happy" signal that tells the electronic fuel pump to pump and the the distributor to distribute...
  5. MisipLC

    Rackin' It

    Installed the rack.
  6. MisipLC

    Antenna Motor Plug - 97 LX

    Can anyone provide the part number for the plug with 2 prongs in the wiring harness that plugs into the motor. It provides power/signal to the motor telling it to go up or down. It is the male side that plugs in here. Looked at the common male plug sheet and could not find a part number.
  7. MisipLC

    Antenna Fix

    So I decided to tackle the broken power antenna. It was not too difficult, but had its challenges. The motor can be accessed from the hole in the wheel well. First the fuel pump resistor must be removed, one screw. The antenna motor can them be removed by unscrewing the silver collar that...
  8. MisipLC

    No Fuel Pressure at Fuel Rail ?

    Okee Dokee, we are stumped. Pulled the engine and have re-installed. Plugged everything back and now have a problem getting fuel to the rail. Using the FSM, checked resistance in the Fuel Pump resistor - good. Checked the Fuel Pump Relay - Good. Jumped the fuel fuel pump and it ran. It...
  9. MisipLC

    Replacing Rear Hub Studs

    While getting finishing up on engine installation, decided to address broken stud on right rear hub. I've had the replacement stud for 5 years. While removing the tire, a second stud twisted off. Glad I purchase 2 - 5 years ago. Yes, you can remove them without taking the hub off the...
  10. MisipLC

    EGR Pair Delete Question

    My son and I are in the throws of installing his rebuilt engine. We are trying the EGR and Pair delete. He now has a question. After reading all the post and threads we have hit a wall. We have pulled everything from under the intake manifold. Looking at the fuel pressure regulator, there is a...
  11. MisipLC

    Bolt Sizes - A/C Compressor Bracket

    Anyone know the size, thread and length of 4 bolts that mount the compressor bracket to the side of ending, the one bolt that goes in the front, and bolts mounting compressor to bracket?
  12. MisipLC

    Broken Plugs Trans Wiring HarnesS

    The male plugs on the transmission wiring harness were crushed during some engine maneuvering. I identified the 12 prong male plug as 90980-11086. The numbers were broken off the 8 pin. However, it appears it is a 90980-10896. Can someone confirm I have the correct numbers before I order?
  13. MisipLC

    Align Flywheel and Torque Converter LX450

    Well I have searched the vast expanse of the forum and internet, only to come away still confounded. i am trying to mate the engine and transmission, ensuring the flywheel bolt holes and torque converter bolt holes align. My son and I can't seem to crack this particular nut. 1. Is there a...
    • MisipLC
    • Thread
    • converter engine flywheel lx450 torque torque converter transmission
    • Replies: 14
    • Forum: 80-Series Tech
  14. MisipLC

    Main Harness - Broken Plug

    1997 LX450 main engine wiring harness. When we disconnected the plug from the sensor, the locking clip broke off. Is there a way to buy a replacement plug for the harness?
  15. MisipLC

    Sound Proofing

    While we wait for our engine to come back from the shop, decided to do some of those "like to" mods. Here is one we did with high cost, high tech material. We used the space age material Frosting King self-adhesive duct insulation. There are a lot of threads in a lot of forums on sound proofing...
  16. MisipLC

    Wanted  Crankshaft

    Need a crankshaft for a 1997 LX450.
  17. MisipLC

    Engine Removal Adventure

    About 6 weeks or so ago, my son heard a strange knock in his 1997 LX450. Out of an abundance of caution he shut it down. We towed the LX to our local Yota shop where they diagnosed a "spun out main bearing on 5th piston push rod." Price to fix, $6,500. Feeling the need for a little father-son...
  18. MisipLC

    Power Steering Issue.

    I have a 97 LX 450 with 160,000. The steering “all of a sudden” became difficult to turn. The problem being worse at slow speeds/low RPMs. The steering shuddered or vibrated at very low RPMs. I Read several threads concerning similar problem, but none of them seem to provide a solution...
Back
Top Bottom