Ghood looking rig and bumper. And yea with the hitch below that might work except I'd need to get pretty fancy with mounting the receiver since the fairlead would be cut out right where yours mounts....
Thanks for the bumper shot, looks great
In the middle of a frame off right now and was hoping to get some ideas on how to fab up a rear winch mount that would still allow me to run a centered hitch receiver.
I did see one photo online of a 40 with the rear winch offset to the passenger side but then I realized they had coilovers in...
Yea I was thinking light industrial coating like they use on heavy equipment too.
Can I use the slide box on an SR? Seems like the spring end would need to travel upward so have the box sloped. Where it would mount on the frame is not flat/level.
Lil John, all fantastic info man I will be taking the slide box into heavy consideration. My 2 concerns are I'm afraid I would rock rash one and end up hosed on the trail not to mention my powder coated frame would need grinding and welding. Second this would take my front back to "stock" (no...
Again great insight White Stripe, yes Alcans have been something I've considered too. I didn't realize they could do reverse eye spring though.
Well it's back to work so I can afford all these parts before the Nor Cal rain starts.
Again thanks for all the input, after reading through your build thread last night I highly value your opinion.
So you are just going to weld up the creeper joint under the frame and call it good even thought you have short front pin hangers? This will leave the spring eyes in a set up that is...
So dump question...if I use the OME springs that have a bushing with 35mm OD and an 18mm ID I would just need to replace the 9/16 bolt with a 18mm pin? Or use a bushing thats 35mm (1-3/8") OD and a 9/16" ID and rock the 9/16" bolt?
How long is the travel slot? Pretty easy to figure out the...
That 40 is filthy, and the 60 he did is sure purdy too. I see he used Alcan springs but I didn't see anything in reference to the Creeper joints, am I missing something.
If I used Creeper shackle hangers in the rear i would this something like tgis image would work in the front...or would this...
That 40 is slick, and the 60 the guy did is sure purdy too. As far as the build goes in reference to the creeper joint I notice he used Alcan springs...
This image is what I had in mind if using the SR style in the front. Blue and red lines would be bracing plate on both sides of the rail. I'm...
Just curious, since I will be making making new shackle hangers and moving them aft, if anyone has ever used these Creeper joints from trail gear? They look like they would act pretty much like the Alcan Orbit Eye springs only on the shackle end instead of the pin hanger end.
I like the idea of...
Thanks for the heads up. I'll have to wait till I get the front axle to figure out what I'll need to do.
When trussing the rear all the way out to the end should i remove the shafts and replace the seals or will it be fine doing it while assembled?
I'll check it out, sounds pretty simple really.
Nice I'll measure the exact wms to wms on this rear I just got from you and when I order a 62 front from cruiserparts.net I'll see exactly how much I need to add to get close to the same width and clear my diff.
And that 2-5/8" extension was enough to clear your diff really well with the perch? Looks like it from the photo. Would it be worth chucking the axle extender in the lathe and taking the excess material off so that it matches the shaft or am I over thinking it?
Thats going to give her a full +3" correct?
I've not had time to read through your entire build thread but damn, metric s#*t ton of info! I am making my own pin hanger and shackle hanger for the 35mmx18mm bushings and will be sleeving the shackle through the frame. Not super big on the offset...