Search results for query: *

  • Users: r2784c
  • Content: Threads
  • Order by date

Forum search Google search

  1. R

    Early '80 FJ40 Parts for Sale

    Early '80 FJ40 Parts for sale: All parts listed below are genuine Toyota parts, NEVER installed 1) Heater Hose - Toyota Part # 90916-01163 -- List $16, Asking $9 + Shipping 2) Exhaust/Intake Manifold gasket (2F) - Toyota Part # 17172-61041 -- List $59, Asking $35 obo + shipping 3) One front...
  2. R

    FJ40 OEM Parts for Sale

    Early '80 FJ40 Parts for sale: All parts listed are genuine Toyota parts, NEVER installed 1) Choke Cable Assembly (Rod Assembly including knob in cab) - Toyota part # 78310-90310 -- List: $78, Asking $45 obo + Shipping 2) Heater Hose - Toyota Part # 90916-01163 -- List $16, Asking $10 +...
  3. R

    Early '80 FJ40 Parts for Sale

    Early '80 FJ40 Parts for sale: All parts listed are genuine Toyota parts, NEVER installed 1) Choke Cable Assembly (Rod Assembly including knob in cab) - Toyota part # 78310-90310 -- List: $78, Asking $55 obo + Shipping 2) Heater Hose - Toyota Part # 90916-01163 -- List $16, Asking $10...
  4. R

    Fj40 oem ps for sale

    FJ40 OEM power steering for sale. Complete kit from 1979 FJ40. Includes pump and resevoir, bracket, PS box with pitman arm, High and low pressure hose, and shorter steering column shaft. Note, entire column not included, just shaft. Asking $900 OBO. Please send PM....
  5. R

    EGR Cooler Disaster

    Ok, I broke the cardinal rule and f'd with the EGR cooler (1980 FJ40). One of the two bolts mounting it to the block snapped, the other came out no problem. My only goal was to loosen the cooler enough to get enough play to allow the EGR pipe to seal to the manifold, then tighten the cooler...
  6. R

    steering shaft removal

    Need procedure for removing steering shaft from steering column on early '80 FJ40. Doing OEM power steering conversion and want to use my original column with donor steering shaft. Thanks Chad
  7. R

    fj40 wheel cylinders - rebuild or replace

    Early 1980 FJ40 - recently replaced drums/shoes on rear, during which I followed the FSM which said to pull the adjuster pistons to regrease. In greasing the driver's side rear cylinder (2 per wheel), the spring pushed the cup downwords, and brake fluid began to leak. I quickly regreased and...
  8. R

    FJ40 - Body Shop Recommendation Needed in Austin, tx

    My neighbor's drunk girlfriend plowed into the back of my parked 1980 FJ40 last night. Need some recommendations for knowledgeable / good body shops in Austin. Thanks.
  9. R

    Rear Drum Brake Job

    Finally got around to replacing rear brake drum and shoes on my 1980 FJ40. Decided to follow the manual which called for the removal of the wheel cylinder adjusting wheel to regrease. First wheel cylinder went fine, but when I removed the adjuster from the rearmost cylinder on the driver side...
  10. R

    F'ing birfs and bearing preload

    Hate F'ing birfs...tried all the tricks to disassemble birfs and nothing. Tried pipe trick...knocked a hole in the road in front of my house, but the birf just sat there mocking me. Tried the FSM techique...brass drift and 3lb hammer...nothing. Anyone have any other suggestions? Also, checked...
  11. R

    split ring on knuckle

    Reading the FAQs on proper order of split ring, rubber, felt seals on rear of knuckle and read that the 'split' in the split ring was supposed to be installed at the 12 oclock position (top of knuckle). Looking at exploded veiw on man-a-fre website, the split is at the 6 oclock position...
  12. R

    Inner Axle Seal Installation

    Have a '80 FJ40 and want to know if I drive the inner axle seal until it hits the ridge in the axle tube, or just tap the seal in till its flush.
  13. R

    Birf Pipe Trick and Knuckle Question

    In the middle of a knuckle service on my '80 FJ40 and have a few questions. 1) When applying the pipe trick to separate the inner axle from the birf, does the pipe have to be metal? Thought I read on a few posts that some people were using Sch 40 PVC 2) Read on other knuckle serivce posts...
  14. R

    Marlin Crawler HD inner Axle Seals

    Guys, Have a 1980 FJ40, doing knuckle rebuild, MC inner axle seals on back-order, now till Jan. Can't wait till then. Anyone willing to part with a set? Thanks
  15. R

    OEM Ride Height Replacement springs

    1980 FJ40, springs are sagging and am trying to find a source for replacement springs with the same ride height. Not interested in lifting the truck, any ideas? Thanks.
  16. R

    2F Ignition Timing Question

    1980 FJ40 - 1st Time setting ignition timing on a 2F and am having a hell of a time even getting a wrench/socket on the Dizzy hold down bolt. I have tried 1/4inch drive sockets, small box end wrenches, etc. I am sandwiched between the vacuum advance on the dizzy itself, oil filter, and oil...
  17. R

    1980 FJ40 - 4WD Question

    If I back the truck up with the t-case in 4H, put the clutch in, the truck immediately stops as if I was applying the brakes. Is this normal? Thanks.
  18. R

    2F Head Locating Dowels, and Valve question

    1980 2F engine, bought rebuilt head from SOR to replace cracked head. Question is, do I need to worry about the height of the 2 locating dowels because more than likely the head was decked? Also, upon reassembly I want to ensure the valve adjustment is not too tight. Yes, I know they are...
  19. R

    Cylinder Head Cracked

    So, just heard from machine shop that my 1980 2F cylinder head has cracks in from the valve seat traveling into the head. At this point they said the cracks are not leaking, but could at any point. I told the machine shop to deck the damn thing, put new valve seals (not seats) on it, and I...
  20. R

    2F Head Bolt Stretch Spec?

    Is there a 2F head bolt stretch spec? Am about to put head back on to 1980 2F and don't know if I should replace the head bolts. Thanks.
Back
Top Bottom