Search results for query: *

Forum search Google search

  1. cptmud

    Official 35" and under!! Post pictures!!

    93 cruiser 2 inch lift 285/75 R 16
  2. cptmud

    What can you tell me from these pictures???

    i had a rough idle problem, and it turned out to be the mass air dlow meter, have you run an engine diagonistic check
  3. cptmud

    Help!! My 80 Died and wont start

    i had a similar issue, and some water ingresion to the mass air flow meter caused a short that shut the car down, it showed no engine check light on ignition, and no spark.
  4. cptmud

    I want to put a part time Transfer case in my 80, What options?

    part time kits are avalible, it involes changing the center diff, changing the hubs to manual hubs, then the centre diff switch becomes the 4wd switch.here are some links on e-bay from the bloke i deal with for the part time kit and hubs. I havnt priced up the option of putting a part time...
  5. cptmud

    pinion still leeking

    if it is still leaking , there might be excevive movement in the pinnon shaft, new crush sleeve might help.
  6. cptmud

    At What Point Does Being "Locked" Matter?

    the use of lockers is greatly under rated. the question of the use of lockers when i get really stuck is not entirly true. Lockers will help you get through and over obstales easier with less chance of damage to the 4wd and to the trackby providing positive traction to all wheels. Without...
  7. cptmud

    Wonder if these Birfs are any good?

    Nothing special about them, but have had some in the cruiser for 2 years now without a problem. I do repack them once a year as part of my serrviceing
  8. cptmud

    stripped Diff (fill) bolt

    cold chisel and hammer works a treat.
  9. cptmud

    Temp gauge readings off???

    not sure what the prob may be, but never trust a toyota temp gauge. Apart from a big flat spot in them, may be a bit of steam build up near the sensor
  10. cptmud

    My Grinder Slipped!

    sweet rig, love the bullbar
  11. cptmud

    Wheel spacers

    thanks guys, just got to workout which ones to get.
  12. cptmud

    Wheel spacers

    Wheel spacers info needed please Thinking of getting a set of 1.5" wheel spacers. Over here in oz they are pricey. so i was looking at getting some from the states. I am look on ebay and found some that suit Toyota Tacoma Tundra 6x5.5 Inch Bolt Pattern -12mm x 1.50 Wheel Studs and Nuts. Will...
  13. cptmud

    Power Steering leak

    iv found power steering kits over here for around AU $35. The reservior might just be leaking from air being pushed back up the line from the leaking box.
  14. cptmud

    Lightforce 170 or 140 photos needed.

    this was when i first started modding the car, the 140's looked a bit small
  15. cptmud

    Lightforce 170 or 140 photos needed.

    this is a pic of a set of 140's and a set of 240's
  16. cptmud

    Aussie with HZJ80 Series GXL

    welcome, nice rig, good to see a fellow aussie
  17. cptmud

    TJM Lockers

    the pro-locker was origanly designed by the aussie range rover and diff guru jac macmarra, with over 50 years experience. TJM bought the rights off him, i will definatly be buying one. will be a good comparison, i have an arb in the front, and will be putting the tjm in the rear. here is a link...
  18. cptmud

    WINNER!!! of the LEDs for Xmas 2007

    im in, thanks for the oppertunity
  19. cptmud

    More Flex

    Just after some imformation on how to get more flex/articulation out of an 80. I have a 2 inch lift. thinking of going to 4 inch. What eles can i do ???
  20. cptmud

    80 Series in Outback Challenge

    unfortantly, the pootrol if the comp 4x4 of choice in australia. they seem to out number all other makes.
Back
Top Bottom