When I purchased my 1972 FJ40 the doors were disassembled. Trying to put the vent windows back in and I don't know the orientation and order that the washers, spring and nuts go on. Does anyone have a diagram that shows the order of the parts and orientation of the little hook washer? Also, I...
Came as a bundle. I never used it, but the truck was running when it was removed. Not sure the make or model. Looks like most I've searched online. Cool Cruisers maybe? Was going to toss it but thought someone might want it. Not looking to make big bucks.
Need to get it out of the house this...
Bought these 2 x 1qt tank liners last year anticipating repairing my tank, but ended up getting a new one. Thought this might help someone in the same process. Paid $32 each, I'll pass along for $50 shipped to domestic US only.
I bought a running motor with this kit on it. Decided to go a different direction. Selling the entire kit as a package.
https://howellefi.com/product/toyota-landcruiser-tbi-kit/
Doesn't include the mechanical fuel pump block off plate. Will also need new intake manifold and adapter to EFI...
I am looking for a driveshaft slip yoke from a later model (74-80) 4 speed driveshaft. It should have the larger 68mm x 60mm 11mm bolt pattern. Needs to have a good U-joint and yoke flange. Shown below is what I need.
As I understand it, this is the pickup tube on my older (72) gas tank, which is around 1/4". I'm in the process of installing a Holley Sniper EFI which recommends 3/8" supply line. Can I run a 1/4" line to the pre-filter without issue or do I need to enlarge or install a new pickup in the tank...
I installed a mini truck power steering box using the Valley Hybrid bracket. I'm just getting around to fitting the fender and the stock opening in the fender is too small. This isn't surprising but I can't find anywhere where anyone else had to cut the opening larger. Before I start cutting...
This kit came with my FJ40 when I bought it. I tried to make it work but ended up going with another option. It was the overlandworks kit originally. I started to modify it because I found during mock up that the drivers seat sat too high. I shortened the width as shown and was going to add...
I need a 2F shroud for a 2F swap into my 72 FJ40. I have the original in good condition I'd consider trading for someone looking for an unmolested one. The 2F needs to be in good condition also. Image of mine attached.
I'm in N Ga and willing to drive a bit to avoid shipping.
I am looking a good condition later model (75+ I think) radiator support with the angled bottom (not rounded) and if available the support rods also. Shipped to 30189 or pickup in the Atlanta area.
I'm migrating from the in-seat separator on my 72 to one located in the fuel filler neck area. So I think I need this one. Anyone have one available shipped to 30189?
Bought the wdorry style bracket and GM pump but cant figure out where the tensioner bracket goes. In particular which bolt holes on the water pump and PS pump. And do I need to space it out with washers and/or bolts? Pics will help as visual.
Does anyone have one of these they could put their hands on and send me pretty quickly? Need to mount my steering column and never had a lower bracket. Shipped to 30189 or pickup around N Atlanta area.
This bracket shown is symmetrical and mine is not, so I'd need one to fit my upper bracket...
Went to the pull-a-part today and picked up what I thought was a "canned ham" pump. Upon inspecting it I realized it looks a little different. Looks like it'll still fit but wanted to make sure. It's a 3/4" diameter shaft, non-keyed so may end up having to go the Grainger pulley method unless...
I have a 72 FJ40 (11/71) that I recently installed a 79 2F w/ 4spd and transfer case in. After installing it I noticed that there wouldn't have been room enough with the crossmember if I had installed the parking brake beforehand. I thought I'd done my research and even today can't find anything...
Transfer case seal is leaking at parking brake drum. I bought the double seals and will be installing in the speedo housing. I also bought the speedi sleeve and wondering how far in I should install it. It doesn't look like it's going to cover the depth of both seals. To me it makes sense to...