Poor truck got hit hard while parked at work. Looking for passenger fender, hood, lower valance, grill and all the little braces for the fender. What do you all got??
Champagne Pearl would be perfect but I’m up for whatever parts are available.
Hey guys, I was wondering if someone could get a measurement for the hole in the air injection nozzle (the part that threads into the head). The rail I grabbed for my 1980 resmog has all the nozzles brazed closed and I was hoping to just simply drill them out. Appreciate the help!
Truck threw a P0715 input/turbine speed sensor. Now all I have is basically neutral stuck on the side of the road as I write this. No worries got a tow truck on the way. Just thinking about my options. Pulled the sensor and it looks like it has been getting long term contact with the torque...
looking for air injection rail and nozzles plus any associated hoses. Also an ABV set up. This is for an early 1980, not sure if early FJ60 stuff will work? Let me know what you got. Thanks!
Cleaning out the garage and these have got to go. In good shape, except short side is missing one lugnut stud. Was thinking $50 for the pair plus the ride. Located in Missoula, MT 59801. Not sure on the best way to ship them.
Figured this would be the best forum to post this in, since you hardcore guys have seen your fair share of carnage.
Background: Changing out my rear diff. fluid the other day and found these weird ground out spots on my ARB carrier and corresponding spots on the housing and cover. How...
I'm putting my FJ40 PTO winch up for sale. This includes the complete front winch (minus cable and chain chocker), short front drive shaft and gear box w/lever. There is one cracked ear on the gear side of the winch, put seems easily repaired. You would need to have the long driveshaft built...
I am parting out an 83 FJ60, a lot of the "good stuff" is already spoken for i.e.:
Power steering=gone
Front axle=gone
F/R drivers doors=gone
F/R Passenger doors=gone
Distributor/Ignition=gone
Fenders=gone
Front driveshaft=gone
Rear seatbelts =gone
Ashtray=gone
Rear gutter moulding=gone...
So, does anyone have any suggestions for removing the cross shaft retaining pin in an RD124. The problem is that when I threaded in the silly little removal tool that ARB gives you, it broke off inside the pin, which is still in the housing. I'm trying to drill it out and use an easyout to...
Today on the way to work I got a check engine light and a trouble code of 25 (over lean mixture). Got home and checked the FSM for the code and got a plethora of different things to check, injectors, o2 sensors, air flow meter, ecu, and a few others. So I checked the air flow meter as per FSM...
engine stalling in reverse A440f Code 25
O.k. so I hid this question in my other most recent post. Perhaps its best to start a seperate one. After installing new R&ps (4.88), I went for a test drive on the fourdyce trail. To my dismay my engine would idle rough and stall when I would put it...
After the 500 mile break in and oil change I decided to run on up to the fourdyce trail and see how they worked. I said only half the story, because only half the axles were done. I was jonesing for some rocks so I went for it in 2lo ARB locked. What a difference gears and a locker make...
Started putting in the locker and gears today and a couple of questions popped up.
First, when I removed the pinion gear, there were no shims behind the inner bearing race. Has anyone ever run across zero shim tolerances before. Should I set initial pinion preload with no shim at first. Is...
O.K. I've been trying to remove the pitman arm on my girlfriends 40 to replace the steering box seal, and I' ve broken two pullers (one cheapo and one $30). I've tried hosing the thing down with liquid wrench for days, heating both the shaft and arm with a propane torch and tapping with a...
I was wondering if any of you out there have removed your smog pumps (60 not applicable) and if so what size belt did you use to in place. Toyota part# or napa #, etc. Also, any of you hj owners out there without EFI do you have a smog pump, if not what belt do you use for powersteering, just...
Trying to get your guys opinions on the best way to respool your winch line (rope or cable) after use. When i had my caple, I would stand in front of the winch and help it spool smoothly, however the next time i used it, it would slip down the wraps and the little mounting screw that holds the...
O.K., a couple of weeks ago my sister's 89 FJ62s transfer case got stuck in 4WD the indicator light is stuck on and consequently 4Hi is always engaged. So, I have an 88 and I thought I'd be smart and stick my control valves (located on firewall) in her truck to see if that was her problem. It...
so its that time of year again and this year I'm really thinking about getting some chains. My question is has anyone ever made ther own it does not seem that difficult. :D ??? Also when running tire pressures in the teens do the chains have a tendancy to slipp off if you get a little wild with...