Hey guys,
Off Land Cruiser topic but I need a mechanic to replace the head gaskets on my 2004 LLY Duramax. What local shops to the Raleigh area would you guys recommend?
Thanks in advance,
Josh
Hey guys,
Had Henry’s muffler in Raleigh replace my cats and muffler on my 1996 LX450 (they were shot). Picked her up from the shop and she drove fine for the first few miles then got a P0125 code on the way home. About 10 miles into the drive home, she blew the hose off and broke the nipple...
Hey guys,
Had Henry’s muffler in Raleigh replace my cats and muffler on my 1996 LX450 (they were shot). Got a P0125 code on the way home and have the o2 sensors ready to go in. However, it blew the hose off and broke the nipple off of the EGR vacuum modulator.
Bought a new modulator and...
Hey guys,
My air compressor and media blaster setup is too small to handle big jobs like wheels. I am ready to powder coat my LX450 wheels and need to have them mediablasted first.
What are your raleigh area business recommendations?
TIA
Searched and haven’t had luck.
Adding a Viair onboard air system to my 80 with the tank in the spare tire location and compressor mounted on Wits End rear quarter panel mount.
Playing around on where to mount the air chucks. I plan on running one in the front (under the hood?) and one in the...
Hey guys,
Have a power interrupt kit on my truck with front and rear connections attached to two solenoids under the hood.
Trying to simplify wiring, have the switches to turn the solenoids on running thru a fuse block from the passenger side battery. Was thinking running 0ga wire through a...
Hey guys,
This a bit off topic. I am need of replacing the tires on my New Holland TC21D.
Any recommendations of places to go in the triangle area?
TIA
I’m the third owner of my 1996 LX450. I knew she needed TLC when I bought her and am slowly fixing her issues.
This winter’s project is swapping in OEM locking axles. But before that, she needs to stop marking her territory/I am removing the factory anti-rust system.
Last night I tackled the...
Pretty straight foreword. Rear is easy, disconnect the sway bars, droop the axle on one side and use a jack to flex the other side.
Front is a bit more involved. I originally tried to install without loosening the brake lines. Gave in and disconnect the brake lines on both sides at the frame...
Hey guys,
I bought a 1995 LC for parts to complete my 96 LX. The LC is in OK shape with the usual 20 year old problems, interior is rough and frame has been tweaked.
It did come with front and rear trail gear bumpers. Rear is brand new, never been installed or painted. Front needs to be...
Having the usual turn signal issue noted many times here. Passenger side rear went out. Replaced the bulb even though the current bulb was not burnt, wishful thinking.
No LEDs other than reverse and front marker lights.
Disconnected the trailer tie in, and now the driver side stopped...
Thanks for advice in advance.
1996 LX450 with 280k miles. Runs and drives fine. Standard oil leak on the front.
I am third owner.
I have the standard EGR codes throwing a CEL. I am cleaning the intake, EGR, etc and replacing all the tubing. Pulling the top portion of the intake off this...
Thanks Mud,
Do u think my diagnosis is correct?
My 1996 LX450 AC stopped working Saturday when temps hit 90+ degrees. Never noticed before, but I have noticed I have no fan shroud on the radiator when I was testing AC system.
AC is charged like it should and the AC was cold after the...
Hello everyone,
If this is the wrong place, please excuse the ignorance.
I have used a "cheap" Chicago Electric welder for the past 10+ years. It has served me well, but I think it is time to upgrade.
I honestly am uneducated when it comes to the differences and brands available.
Here...
I was advised of this board by jfg80 and am finally saying hi.
I am new to the FJ ownership, but this will be my 3rd vehicle build/resto.
I purchased 1996 LX450 in need of some TLC in November. I am currently in the middle of a front axle rebuild, gaskets, bearings, flipping birds, etc.