Search results for query: *

Forum search Google search

  1. M

    whos 70 series with camper in SK

    you guys should come and hang out in Whitehorse sometime.. there are a lot of these kind of rigs up here.. 70 series, Unimogs and the ubiquitous land rover defender... they all roll through here in droves! and most of them have these euro plates on the front. some of the mogs are just huge! i...
  2. M

    EDIC acting up, tried everything, 2 days time left

    I took my edic entirely off and . then i drilled a small hole in the firewall and a small hole in the dash. i fed a stiff steel wire/ bar through the dash through the firewall and welded the wire to the end of the ball joint at the injection pump. i can push and pull the injection lever from...
  3. M

    Lubro Moly Purge

    Dude, i worked at a european car shop, actually i worked at a couple of them and we used this stuff religiously. i have personally seen VW tdi's come in huffing black and making a sick stuttering mess.. drive out after running a bottle of this stuff smooth as silk and clean. my boss swore by the...
  4. M

    Realtime help! Bj70 drive axle U joint #

    ohh im in hamilton ontario
  5. M

    Realtime help! Bj70 drive axle U joint #

    i bit the bullet and bought genuine toyota parts. what happens if i replace just one.. is the other going to pooch soon too? waiting another day is not an option!
  6. M

    Realtime help! Bj70 drive axle U joint #

    is precision # 389 the right one too
  7. M

    Realtime help! Bj70 drive axle U joint #

    awesome.. thanks!
  8. M

    Realtime help! Bj70 drive axle U joint #

    is there an aftermarket number that you know of.. my truck is broken and i cant wait for the stealership, i called them and they said it is the same as a 60. The local driveshaft place has never even seen a landcruiser axle... aftermarket crossreferenced number anyone? TIA Jon
  9. M

    Realtime help! Bj70 drive axle U joint #

    does anyone know what the part number is for an aftermarket ujoint? does spicer or any of these places make a u joint and if so does anyone have the number handy.. any help would be appreciated. Jon
  10. M

    Lubro Moly Diesel Purge

    to illustrate my point, on a cold day, lets say -20c, you go out and start your truck.. it starts and you rev it to 1000 rpm with the throttle lock and "warm er up".. you go inside and grab your coffee, the paper.. whatever, when you come out after between a minute or five, where does that...
  11. M

    Lubro Moly Diesel Purge

    revving a cold 3b to 1000 rpm at startup is not so that it can "shake", hahaha. its to keep piston velocities low in a cold bore, and allow combustion to warm up the burner cups to a point where combustion is even. adding more fuel cools the chamber down and create incomplete combustion and...
  12. M

    Lubro Moly Diesel Purge

    when its cold, no it wont hurt it.. especially not a 3B. the crank and main journals are engineered to operate with oil pressure as low as 4.3 psi! yes FOUR POINT THREE PSI. they have ample surface area and good tolerances to deal with this, and thats why they last forever, because even the most...
  13. M

    Lubro Moly Diesel Purge

    try this.. when you start your truck, no matter how cold it is, resist the urge to press the accelerator or the PTO idle up, if you have to give the truck some fuel to get it to fire, so be it.. but IMMEDIATELY let off and let the truck idle at its factory set low warm idle. note: it will be...
  14. M

    Lubro Moly Diesel Purge

    the injector tips is where the carbon is, and the fuel is going to push most of the carbon out, undo the line for the injection pump, dunk the line into the tank right to the bottom and run at varying RPM till it shuts off, reprime.. drive. i say this because even the most foul diesels we...
  15. M

    Socks.

    right now with all the snow drifts and melting snow.. if im going to be outside i wear regular old cottons and then heavy wool overtop and then goretex kneehigh oversocks by "mustang survival" then regular boots over that.. completely waterproof and breathable.. they rock, awesome for when...
  16. M

    On board welder

    the welder that i have has rewound internals and 12 x 50 amp diodes and can push 300 amps at 30volts. its not a regular alternator you might get 100 amps out of a regular alternator, and it will have a poor duty cycle. if you want to try building your own alternator welder.. go for it...
  17. M

    So, if your GF had $200 to buy you a 2m radio...?

    I have a VX-6R (tri band, wide recieve 5w) and a tm 2750 wich is a 60 watt 2M transciever.. with no tone board. if youre into offroading and you go into deep mud and water.. a small waterproof handheld like the VX6 is (in my experience) a better buy than a clunker 2M rig for a first buy. sure...
  18. M

    On board welder

    onboard welder I Have an onboard welder in my BJ70. it really works well.. in fact i can blow a 5/32 rod through 3/8 plate no problem. also i have tig welded with it a few times. Its a real joy to have in there and ive used it many times. my welder is completely homebuilt and it resides...
  19. M

    Build UR Own RooftopmTent

    I really like your DIY idea.. i think that a rooftop tent could be set up really easily.. ive been giving it alot of though lately my friends once built an entire awning for thier cabin cruiser.. sewed the canvas and windows in .. all the screens... they literally saved themselves hundreds...
  20. M

    Replacing head gasket B engine; any tips?

    when you replace the headgasket you should take the head to a machine shop and have it checked for trueness (flat) before bolting it back on, also checking the pre burner cups for any type of cracking is also recommended.. the burner cups tend to fail and fall into the cylinders, replacing them...
Back
Top Bottom