my EGT temp sensor is being stupid and I would like to fix it. My assumption is that these wires don't have polarity as they are only looking for delta Voltage, but do they? Can't find what I am looking for in the FSM
I've got a 2008 GX470 with the mark levinson and it has the AUX in. Mine is too spotty to work reliably anymore. It looks like this.
Im trying to get it to work or to replace it with something better (that doesn't cost $200 either). Wanted to see if people had solutions to this. My thinking...
Just below the heater control valve on the firewall. Its pretty soft and its pretty obviously leaking. I can't find what it is PN wise or dimension wise.
I need someone smarter than me to help me with coil selection.
Where I am
Stock weight(ish) 97
Currently running TJM 50mm progressive 110kg + rear coils and stock weight progressive 50 mm fronts.
Want
2 inches settled rear lift with load, 2.5 without
2 inches settled front lift
Decent unladen...
So with my rear panhard lift bracket installed the Cruiser drives SO much better. It tracks straighter, it doesn't bob my head around nearly as much and it's just so much more civil. BUT it also means that my panhard mount on the axle side is up higher and now hits a crossmember under full...
Question about trackbar length and alignment. I just put on a dobinson front trackbar (apparently they are trackbars in the front and panhards in the rear...) - rather I had someone do it because I didn't want to. They didn't do a GREAT job centering it and its offset passenger a little less...
I just had my PS pump replaced because it was leaking like crazy (it was a 3rd party reman, but is now a Toyota part). Now the pump stopped leaking but the leak on the floor is getting bigger. Turns out its coming from here. It was coming from here as well before. The trouble is that both of...
I know there are MANY threads dedicated to this and I've waded through many of them, but I also know that people here have tried all kinds of solutions and have probably already found the answer I'm looking for, so why not. This is my 97. It's on 33's and current a TJM 50mm progressive rate 50...
I hate having this useless hole in front of the shifter. It mostly just gathers trash and I want to repurpose it so it doesn't get used that way anymore. I don't even know what this was supposed to be used for but its not really good at anything. Does anyone make something that fits in there...
If your visor warnings are worn out like mine were you may want some reprints. These are 1:1 scans of mine, but cleaned up as much as I could to make them complete and ledgible. You can print the white on yellow cardstock, or print the yellow on white cardstock.
Was looking up some towing information in the user manual as a reference for my 08 GX470 and I found this nugget under towing
"●Set the vehicle height to the “LO” mode and turn off the rear height control air suspension to prevent the vehicle height from automatically changing."
P.185
is this...
I've had a problem on the 80 ever since I lifted it many years ago and its getting worse. I want to see if anyone else has had a similar problem and solicit ideas to solve it.
This is the TJM XJS 50mm progressive-rate front springs. As you can see, my bump stop tower is hitting the spring...
I've been thinking about getting airbag helpers for the rear springs. Reason being that I really like my rear TJM progressive springs - great flex, great unladen ride, etc. - but they sag pretty badly under load and I do tow with it from time to time and/or put a lot of people and things in it...
A friend is out of state looking for some help diagnosing an AHC issue. Took the battery out, put it back in and the AHC wont raise. Blinks twice when you try to go from L to N then stops and nothing happens. Is there a calibration procedure for the AHC? or is he looking at a hardware...
I need to make sure I put the shock mounting plate for the rear shocks on in the right orientation. I had someone else take the plates off and label them, but I think they were labled backwards. I installed them like so.
This is the DS.
The open end of the bolt in the bracket is facing the...
1. Shifting hard. especially between 1 and 2. What should I look for? Fluid appears to be at the right level and its the right color and smell. I wonder if it's just a little low. Any other things I should look at? It was rebuilt by the PO at something around 150k according to them and...
What do you need to take apart to get the center HVAC vent/bezel. The one that shares the clock and vent. I bought one of these, and I want to replace the clock with it (the face is very close to the same size).
I tried to pop it off but no dice. I would prefer not to have to pull the...
So I don't know if this has been posted already, but I was recently up at Weber state Talking to John Kelly about something I am writing and I found this sweet cutaway of the A343F so I took a picture. On the transmission, I just noticed that it has a QR code to a video of a class where he...
So I know there is a whole other tread on this, but I wanted to write down my concise experience with my install. I had new seat covers from Land Cruiser Heaven installed this summer and while they installed them I had the upholstery shop install seat heats, but not the wiring. The ones my...