This is my 1fz,
Pretty sweet hey,
Except it runs like a dog,
1993, manual, aus spec 80
Got it on the road ran beautifully for a few weeks, until the start of this week when I noticed it bogging accelerating from the traffic lights at the end of my street.
I’d describe it like a carby car...
Social media sucks, return to forums I say.
I own this.
Its kinda falling apart,
I bought this with visions of it becoming a replacement, all those things I had done on the previous car questionably and learnt from could be done better.
30 minutes into ownership
14s lol
Hey guys.
I’m attempting to 4 link the rear of my 80.
So far i have a rough idea of what I want to do but you Americans seem to play around with 4 links a lot more than us Australians.
Afaik no one still has really done much on it on the 80. I’ve only ever seen ones with a frames, or still stock...
Found this and.thought it might interest some of you.
Bloke that built it apparently made 300hp with a 3071 and 12mm rotary pump off a td42, I'll try post the video.
Anybody on here done this to their 1HZ or other IDI engine?
Supposedly helps bleed off steam behind the precups if it starts getting hot and stop the snowballing effect.
I know this has been discussed before but cant get a clear answer on it. Had reports this it can be bolted on and ran as is, to it needs components swapped, to it wont work at all. I know that the 6 head things will need to be changed as the injector lines are smaller. Can anyone that has 1hz...
Hi, currently swapping my wiring loom over to a diesel one and decided to test it before refitting everything, I have no power getting to the ignition barrel and only the ECU-B, Defrost and brake fuses have power. Fuse able links are fine and so is the 50amp main fuse, is there anything else...
Alright guys my 80 is making a gear/drivetrain noise that is noticeable from 50 - 110+km/h. It only occurs when maintaining a constant speed with low load on the motor. Its a 91 manual hzj80 and the noise occurs in any gear. Have checked oils in everything and they are clean at the correct...
Hi, just put on my new gturbo and it goes great, only thing is that its boosting past the end of the gauge I have (20psi)
What is the standard waste gate pressure in them? And is it possible to lessen it.
Thanks
Hi,
Just got my 1hz conversion up and running.
Its got a gt2876r on a highmount manifold, 3 inch exhaust, 600 x 300 x 76 intercooler.
Currently only running 10 psi at the intake manifold, Goes about the same as my mates landcruiser running a dts turbo @ 15psi. Very little soot out the...
91' Gxl 80 Series
Bought cheaply in a sorry state late 2012
It currently has.
- 2 inch lift
- 33's
- Tjm rearbar
- Terrible paint
- Sliders
Some interesting stuff that you US guys didnt get.
- The 3f is carby, not efi, Even so it gave better fuel economy and had more power than the 3fe...
After changing from a holley to aisan carb about 3 months ago, My cruiser has sat pretty much un-driven. Spontaneously decided I would drive it to work today and have noticed a stutter like symptom cruising at around 70km/h. Its as if I took off and immediately put down my foot. The drive train...
Can anyone tell me if a manual 3f 80 series has an inspection cover on the bell housing?
My cruiser has developed a large hemorrhage from the bellhousing area and I would like to get a better look inside to find out where its leaking from.
Hi, my dad has been having issues with intermittent central locking and power windows lately. It would randomly stop working while driving, then work again after 10 minutes of being parked. Yesterday it packed up completely. We have tired swapping the master switch and green control box from my...
Hi, have just installed an aisan carby on my 3f, the previous owner had a holley on it.
It just wont idle right. I have got it to the stage where it wont stall but the idle mixture screw is about 4 turns out and it smells like its running rich. Idle fluctuates from 600 - 1200 rpm and has a...
Hi
Iam replacing all the heater hoses on my 3f 80 series and have found this hose that goes nowhere.
Photo was taken from under the engine.
It starts at what I think is the oil cooler is. Then works its way forward, behind the harmonic balancer and is capped just short of the water...
The vapour vent that connects to the fuel bowl of the carburetor, What would be affected if it was just capped off?
Also if it is needed could something be made to work just with off the shelf bits and pieces?
Hi, Im currently trying to remove the butchered holley carb set up on my 3F and replace it with a stock aisan carby. Bit confused on what connects up to what, Ive figured out the accelerator, choke and fuel cut, but I am missing a heap of vacuum lines and emissions control thingys , Can the 3...