Hi all I wonder if someone with experience can explain the best way to remove the cracked intercooler pipe from a 2006 hdj100 with an fte engine? It is the pipe under the RHS front guard.
Just paid $600AUD(Ouch) for the replacement t and wanna swap it out to get a roadworthy. Thx.
Hi I just got a kenwood 10.1 inch headunit. It has a GPS and also a PINK VSS wire on the harness.
1. Does anyone know where to put the wire?
2. Do needs some type of signal converter to make it work?
Anyone suggest some steps to resolve this? Thx
Ps. I am told VSS checking can be turned off...
Roger that. Will do. Thx
Self hijack of my thread here.
Hey Scott,
Heading down the gtx3582r gen II with 6boost manifold and 14psi turbosmart waste gate.
I think you have played with Haltech from memory. I think I will use their new transmission control features in my elite 2500 rather than...
Hi, I am getting platinum racing to make a new bracket to fit Coil on plug for my new haltech elite 2500 ECU project.
He would like to know the gap between cylinders so that he canake me a bracket. Does anyone know the dimensions (I do not trust myself to get it correct).? Any one have a...
Yep, from AU. Thx, I'll jump on to it now. Btw, I'll likely persue the witts end turbo over the next few months as this looks like quality kit. Keep you posted.
Yep, ODBI, Dalton's the timer in my area has completed a few tricks. I believe one was a turbo ODBI truck with an auto and injected LPG. They had success using a motech ECU as a piggyback. I think the only thing that worries me is how the factory ecu will handle idle if I remove the AFM from...
Thanks Scottryana,
With this approach, can you advise on what sensors move over to the haltech? Are there any that the haltech should share? I would like to leverage full sequential firing, delete the air flow sensor on the intake, use the haltech's MAP and install an air temp sensor instead...
Hi folks,
Heading down the road of an eventual turbo solution but first I am going to replace the stock ECU with a Haltech elite 2500, basic harness, wideband O2 kit and 6 HT-020114 high output coils with built in igniters. Will drive around for a few months and then save bucks for a witts-end...
Hi folks,
Heading down the road of an eventual turbo solution but first I am going to replace the stock ECU with a Haltech elite 2500, basic harness, wideband O2 kit and 6 HT-020114 high output coils with built in igniters. Will drive around for a few months and then save bucks for a witts-end...
He folks, I live down under. Have a 1994 1fzfe (flapper MAF) with all standard except I have dual fuel, vapour injection lpg.
1. Is anyone who drives on my side of the road gonna fit this kit?
2. Do you foresee and interference with the steering column booster or other items?
3. Any idea how...
Hey mate, that's fantastic work! If you write it up, I will have a crack at doing the same to my 1994 80 series. I wanna turbo too. Have been wondering which is best, turboglide or axt. Have you weighed the pros and cons of each? Love to know your conclusions
Chris
folks,
I have just had my stock 1994 80 series Dyno'd. My truck is running petrol and lpg.
It has done 380,000kms. I have attached the chart and would welcome your thoughts on if the performance is up to scratch.
note i pulled the front drive shaft because the dyno was a 2wd version, so...
Thanks Baktasht,
BTW, I wonder, on a side note have you shipped any of your turbo kits to Australia? Can you PM so we can discuss this as an option?
Cheers
Hi, Sorry to awaken this old thread, but I just installed a fuel filter into my 80 series (1fz-fe). Anyway when reattaching the input fuel line it pushed the bottum alignment tab, so I guess it is not completely alligned. However there is no leakage and the truck runs fine (seems too). I cannot...
Found this vaccuum diag on the web.
https://plus.google.com/u/0/104733112959415786457/posts/43hr7Kz2gD1
I see the TVV valve is supposed to have two tubes going into it. I wonder if this tube broke off the tvv valve? Can anyone confirm if from my video the valve that has the tube terminated...
Hi Mate,
Sorry. I'm crap at this multi media stuff.
Here is a link to a short camera video. If you drag the video slider by hand you may be able to get a better idea of the area below the inlet manifold (just forward of the Fuel filter)...