Search results for query: *

Forum search Google search

  1. 60/40GUY

    Courtesy door light fuse location

    It was DOME 1 - 5amp under the hood. Thanks for the help. The LX has a few more fuses than the 40.
  2. 60/40GUY

    Courtesy door light fuse location

    While replacing the courtesy door light bulb I inadvertently shortened out the bulb holder. I cannot find the fuse location in the owners manual. Does anyone know what fuse box and the fuse location? Thanks
  3. 60/40GUY

    BudBuilt Group Buy (Closed)

    Put me on the list for a full set of skids - I am thinking light steel at this point. Thanks Frank
  4. 60/40GUY

    200 series LC rim size

    Thanks - that explains where I got the impression LC rims measured 8.5. The LX is 8.5 and I mistakenly thought the LX and the LC rims were the same width.
  5. 60/40GUY

    200 series LC rim size

    Thank you. I thought I read somewhere that LC rims were 8.5 inches wide. I want to put 18 inch wheels on my LX and am planning to tow a travel trailer. So for stability I was looking for the widest stock rims I can find. It sounds like I can look at Tundra rims as well.
  6. 60/40GUY

    200 series LC rim size

    Is the width of stock U.S. Land Cruiser rim 8 .5 inches?
  7. 60/40GUY

    FJ60 with 2F to 3FE from 1992 fj80

    You’ll also need the gas pedal and cable.
  8. 60/40GUY

    For Sale 2009 LC200- One Owner, Kansas City

    The seller and I agreed to $28K before I made the deposit.
  9. 60/40GUY

    For Sale 2009 LC200- One Owner, Kansas City

    I hope it went to a Mud Member. From the information I saw the truck looked nice. Late last week I put a deposit down on the truck. Then Saturday night the seller returned most of my deposit with very little explanation. I am still not really sure why. Anyway I hope the new owner has fun...
  10. 60/40GUY

    Towing experience

    Does anyone tow a travel trailer with a GX460? I am looking to pull a 4200 lbs 23 foot travel trailer. I am sure the GX would do fine on the flat - but what about the hills and out west?
  11. 60/40GUY

    Builds Goat. A 1967 survivor FJ-45 LWB

    Hi Nolan - read through this whole tread. What a great job on the 45. I really appreciate that you are trying to keep the 45 as an original survivor. It looks like this truck is a perfect candidate for this. I wish my 45 was as complete and as original as yours. I was thinking of clear...
  12. 60/40GUY

    Quick engine question

    Thanks Mark - that is what I needed to know. It seems odd to me that the gear set timing marks do not indicate TDC of the compression stroke of the #1 cylinder. I'll wait to get the flywheel on before I install the distributor.
  13. 60/40GUY

    Quick engine question

    In my original post I should have clarified that I am looking for TDC on the compression stroke. The engine is on a stand - so no flywheel attached. Rocker arms are all out so I cannot check which valves are being actuated. I am looking to install the distributor so I need to find TDC of the...
  14. 60/40GUY

    Quick engine question

    Searched but could not find the answer. Is the #1 cylinder at TDC when the cam and crank gear timing marks are aligned?
  15. 60/40GUY

    Tranfer case flowith over

    I believe the o-ring on the idler is leaking from the transmission to the transfer case. Has anyone else had an issue with the Mark's gear set (or Gearmaster} leaking? It does not seam like there is enough squeeze on the o-ring when I set the idler shaft into the transfer case cover.
  16. 60/40GUY

    Tranfer case flowith over

    I have a H55 mated to a 34MM split case transfer case with a set of Mark's gears in the transfer case. Gear lube is being pumped from the transmission to the transfer case. What is the possible cause? Bad out put seal on the transmission? Bad o-ring on the idler shaft in the transfer case...
  17. 60/40GUY

    Show us your engine bay!

    85 FJ 60, 2FE, H55, 62 axles
  18. 60/40GUY

    2FE help

    A quick follow up post on my motor stumbling issue. I solved my engine problem today. When I built the 2FE I used the 2F valve cover and the PVC engine venting system in its entirety . I had a vacuum leak in the plumbing from the valve cover to the intake runner tube. Once I fixed the vacuum...
  19. 60/40GUY

    2FE help

    Collected a bit more data still no resolution - Engine Vacuum at idle = 16 - Engine idles at about 750 RPM - VSV checks out per FSM inspection - fuel pressure at temp using service wire = 41 psi - FSM range 37 - 46 PSI - fuel pressure at temp with vacuum removed from FPR = 41 PSI - FSM range...
  20. 60/40GUY

    2FE help

    60 toy ota - no codes - no cel. You can accelerate until the engine hits about 2000 rpm. Then it starts to cut out. If I kind of feather the accelerator back and forth I can get to run a bit past 2000 rpm. It does this when the motor is hot or cold. When it is cutting out it kind of acts...
Back
Top Bottom