Search results for query: *

  • Users: Ryan S.
  • Content: Threads
  • Order by date

Forum search Google search

  1. R

    83 FJ 60 driveshaft

    I don't remember if it is front or rear, but it is 46" flange to flange. $30 plus shipping. email direct to oneguyry@yahoo.com Located in Spokane, WA
  2. R

    Trying to ship my FJ 60 to Dallas

    Helping arrange shipment for a potential buyer. Would ship from Spokane, WA. Any suggestions on carriers? Anyone headed that way who could pull a trailer? Thanks.
  3. R

    16x 8.25 8 hole rims

    American Racing chrome rims with center caps. $50 Located in Spokane, WA
  4. R

    Aisin carb

    Off my '83 fj60. Worked when it came off. PM or email direct at onguyry@yahoo.com for pictures. $90 plus shipping from Spokane, WA
  5. R

    Selectro locking hubs

    They were on my FJ 60, but were a little too long to get the C clip back on the axle shaft. Maybe a better fit on an FJ 40? $50 plus shipping from Spokane, WA
  6. R

    Clean FJ 60 frame

    $150. Surface rust only. Rear leaf spring hangars were cut during part out. Small 1/2" sawzall cut in front, driver's side body mount bracket. PM for pics or email direct at oneguyry@yahoo.com. Located in Spokane, WA. Will deliver for free within 50 miles.
  7. R

    83 FJ60 Drivetrain rebuilt

    1983 Landcruiser $5200 NEW PARTS REBUILT MOTOR: 30K BALANCED, HEADS SHAVED (04/04) DISTRIBUTOR CAP AND ROTOR (04/04) IGNITION WIRES (04/04) MOTOR MOUNTS (04/04) A/C PULLEY (04/04) RADIATOR (04/04) EXHAUST HEADERS (04/04) SMOG PUMP ELIMINATOR PULLEY (04/04) CLUTCH...
  8. R

    A pillar gauge pod for sale

    The new A pillar gauge pod. Black. Never installed. NEW 1 1/2" mechanical oil pressure gauge included. $65 plus shipping. Located in Spokane, WA Pm for info.
  9. R

    Knuckle SST For Sale

    Centering tool for front axle rebuild. Never been used. $80.00 Located in Spokane, WA PM for details and for a picture, if you would like one.
  10. R

    Battery isolator shorted out?

    Took one of my other rigs for an emissions test yesterday. It's a diesel with an isolator and a winch. The emissions techs needed a 12volt power source, and since there is no cig lighter, they had to hook to the battery. I couldn't exactly see because of the hood, but it looked like they were...
  11. R

    Timing advance and throttle response

    The timing has been at 7* BDTC after slowly bringing it down after the rebuild a few years ago. The heads have shaved, and if there was any adavance above 7*, there would be pre-ignition knock while pulling a trailer. Well, I'm taking a road trip this weekend, w/o a trailer, and thought I'd...
  12. R

    Water pump bolt size?

    Anyone know the size/threads for the bolts for the water pump to the block? Looks like I'm missing one at the top of the pump. Going on a road trip tommorrow and would like to replace it. Thanks.
  13. R

    Rocker cross-section pic

    My rockers are starting to rust through and I'll sometime replace them with sliders. Been looking for that picture of the rocker panel cross-section to show my welding buddy, but no luck finding it yet. Can someone repost it here? Thanks.
  14. R

    Report: Valve adj. running vs non-running

    About two months ago a buddy of mine, also an experienced mechanic, adjusted the valves while running. That's just the way he's always done it. Well, last night I got a wild hair up my a__ and decided to check them with motor not running. Some were right on and some not. There were 3 that...
  15. R

    H55f input shaft spline count

    What is it for a gasser h55f? Any one know? Thanks.
  16. R

    I'm a synner

    As of last night, the motor, tranny, transfer, and rear diff are filled with synthetic oil. I've been running the motor, transfer, and front diff on full syn since they were rebuilt. However, now I am full of syn. That's all. Except for filling everything with a little hand pump on the...
  17. R

    '72 Bronco Sport For Sale

    Posting for a friend; he's thinking of getting a cruiser Full restoration. Only 40,000 original miles. Located in Missoula, MT $25,000 Email ken@adventure-education.com for specifics.
  18. R

    Sudden drop in oil pressure

    Before the drop, gauge was about 3/4 up between L and H at operating speed. Noticed while driving home yesterday, that the needle was on the bottom hash mark. There is now little or no fluctuation of the needle from idle to operating speed. Oil level is good. Everything else is normal--no...
  19. R

    Cummins Industrial Tools Winch

    So this Cummins Industrial Tools is mostly a traveling Harbor Frieght, or so it seems. They offer this winch. http://www.amazon.com/Cummins-Industrial-Tools-Heavy-Truck/dp/B000FOIINM/sr=1-1/qid=1172164317/ref=pd_bbs_1/105-7422868-7754849?ie=UTF8&s=automotive POS or a decent value?
  20. R

    No 4WD!

    All feels normal when I shift into 4WD, but for some reason it does not engage. Transfer case was rebuilt 1 1/2 years ago, and has worked perfect until now. My guess is that I will need to pull the case and look at the inards for a problem. Hopefully someone here will have other suggestions...
Back
Top Bottom