1970 FJ40 Landcruiser, Smog exempt, SB Chevy 350 w/quadrajet, SM420 transmission, 3 spd transfer case (with t-case saver), tilt wheel, saginaw power steering conversion, spring over axle conversion, 4 wheel disc brakes, Dana 44 front end (built by Dynatrack - cut and turned w/new front...
1970 FJ40 Landcruiser, Smog exempt, SB Chevy 350 w/quadrajet, SM420 transmission, 3 spd transfer case (with t-case saver), tilt wheel, saginaw power steering conversion, spring over axle conversion, 4 wheel disc brakes, Dana 44 front end (built by Dynatrack - cut and turned w/new front...
1970 FJ40 Landcruiser, Smog exempt, SB Chevy 350 w/quadrajet, SM420 transmission, 3 spd transfer case (with t-case saver), tilt wheel, saginaw power steering conversion, spring over axle conversion, 4 wheel disc brakes, Dana 44 front end (built by Dynatrack - cut and turned w/new front...
Trying to find out if this is a stock L/C FJ40 Master and slave cylinder, its out a 1970 FJ40. Please see attached pictures, the slave cylinder is connected to an SM420/SB350 combo. Also have another questions, both JT Outfitters and Cool cruisers sell a completely new clutch master/slave...
I need to replace my master/slave cylinder in my 1970 FJ-40. It appears I have the stock slave cylinder, the reason I ask is because I have an SB350/SM420 transmission combo.
Does anyone know if the slave cylinder would be a stock FJ40 even with the 350/SM420 conversion, or how I can...
I have a 70 FJ40 with what appears to be the stock clutch master and slave cylinder. The other day I parked the cruiser and the next morning I only had about 1/2 the throw on the slave cylinder to engage the clutch. I re-bled the system and it worked fine again until the next morning and the...
I am selling my 1993 80 series, it has never seen a rock or piece of dirt in its 14 years of life. A potential buyer stopped by this evening and we could not get the differentials to lock.
After switching the selector to rear or rear/front, they started to blink on the dash and never stopped...
Just got finished running Rubithon and my Tcase kept popping out of gear. Its a vacuum shifter, I ended up placing a bungie cord on the shifter lever and attached the other end to the roll cage and after this McGyver manuever it worked fine. Obviously something is not working properly, does...
Unfortunately, the time has come to get rid of the FJ80 with 179,000 miles on it. Fuel prices are definitely one of the reasons, 12 MPG is painful with three kids that need to constantly be driven all over town!!!. (I still have my 70 FJ40 :) ) I am in Roseville, California and my wifes vehicle...
I need some opinions on this one... I have a spring over on my 70 FJ40. Currently sitting on level ground, I have 4 1/4" of upward travel, and 5 1/4" of downward travel available on my FRONT shocks. Which is roughly a 40/60 mix. Does this sound about right? I am trying to get good upward...
I am trying to extend my winch cables on my Warn 9000X. My battery is located behind/under my passenger seat and the warn cables are about 5-6' too short. I tried going to Kragens today and they only sell a 36" #2 battery cable, I need a longer 48-60" cable. They did have a #4 cable that...
I extended my rear axle breather (more towards drivers side) with a longer line on my 70 FJ40 and noticed there is another breather port that holds the brake line junction box to the axle housing. Is it necessary to have two of them or can I just get a bolt and plug it off? I dont ever recall...
Does anyone have any updated pictures of the rubicon? I saw a couple on Pirate from early May and the trail had a LOT of snow on it! Should be very interesting....
... and whos going? I am on the Thursday morning breakfast run with Bill Jackson.
Its been six years since I have been up...
Trying to find a car hauler to tow my 70 FJ40, does anyone have any recommendations for a new trailer? I am in the Northern California area. Tried Pac West trailer, $2300 out the door for a 16' wood plank, 7000# capacity, tandem axle, elec brakes, etc... $3300 for a steel deck.
If anyone...
Is anyone running a linelock brake setup? My brother has a 70 FJ40 with an NP205 tcase and Ford 9" rear end and needs some type of ebrake setup to run organized TLCA events. Does anyone have any ideas? I thought a linelock might be a helpful solution.
If anyone has any suggestions for...
I tried a search on this, but had no luck. Does anyone know the weight of a V8 FJ40 with NO hardtop or hard doors? I had heard somewhere around the 4,000lb range?
Trying to figure out if my 2 wheel drive fullsize 1/2 ton GMC 5.7L Vortec would be strong enough to trailer tow my FJ40? I am...
Just got finished installing a new set of rear Ubolts, does anyone know what the torque specs should be? I thought it was around 70 ft/lbs???
Thanks
fman