Search results for query: *

Forum search Google search

  1. D

    Is any slop permitted in idler pully?

    I couldn't figure out the search terms to try to find this answer. I have removed my belts from a 90 FJ62 with 220K miles and I notice that both idler pulleys can be wiggled from side to side about 1/16 of an inch. Should I replace these or is this normal?
  2. D

    Schematic for wiring harness?? - Ignition power now dead

    '90 FJ62 ...... Does anyone have a schematic for the wiring harness? There is nothing showing wire routing in the FSM. The black wire (may have a yellow tracer) that feeds the ignition switch and most of the dash accessories, I attached an accessory load to this wire that drew too much...
  3. D

    90 FJ62(fuel injection) - Fails smog CO too high

    This has not been my day/month/year. My FJ62 just failed the smog emissions test. The CO high speed test failed. Standard is 1.20 and it hit 1.54 on high speed. Least year the CO reading was 0.5. A giant gain over the past year. Any ideas? THere has been no check engine light and I...
  4. D

    Need color code & routing - wire to fuel pump

    I cannot find wiring harness names, location and/or function in the FSM. I want to find the wire to the fuel pump. I found one that looks like it might be the one but I am not sure about it. The suspect wire appears to run from somewhere on top of the gas tank to just under the rear of behind...
  5. D

    Front axles won't go in after knuckle rebuild

    '90 FJ62 .... in the middle of knuckle rebuild .... I must be missing something. I have replaced the knuckle bearings and started to put the axles back in but the axle shaft sounds like it is hitting on something inside the differential. The birfield is sticking out about 1/2 inch and it...
  6. D

    Knuckle rebuild - how do I press arm into top knuckle?

    I am at the point where I have driven in the new knuckle races and am ready to insert the knuckle bearnings and replace the housing. The tech section is a little vague in this area: http://www.birfield.com/~morgan//tech/axle/part5.html When I removed the original bottom knuckle plates, the...
  7. D

    Locking lug nuts

    Can anyone recommend a good set for 90 FJ62? I can't seem to find anything searching Google with any standard search I can muster
  8. D

    Bull guard question

    Hi, I guest-attended a meeting a year ago and enjoyed the people and nice equipment on display. I primarily use my FJ62 as a work truck and not much hobby type stuff, however, I have decided to take it on a long (first) trip to mountains of Mexico. Someone on the 60 wagon forum told me to...
  9. D

    Wanted  Dallas area - need 90FJ62 bull bar/opt w winch

    Anyone in the Dallas area know where I can pick up a used (can be scratched or dinged, ok) bull bar for a 90 FJ62. If the price is good, I could go for a winch as well. THANKS!
  10. D

    Where to begin - '90 FJ62 tune up

    I purchased a '90 FJ62 about a year ago with intent to "tune it up" and just never got "around tuit". I have put over 7K miles on it (bought at 203K, now has 210K). I am getting ready to drive it on a 3K mile trip and decided now is a good time to revisit tuning it up. Where do I begin ...
  11. D

    Need gas cap for '90 FJ62

    Who can afford a new one! Thanks!
  12. D

    Is 3FE manual available in PDF form & other trivia

    I posted this at the end of another old thread and no one responded. I know folks don't appreciate when you come to a forum and ask a question without first searching, but I have been searching this forum and others for several days looking for a 3FE engine manual in PDF form. I found a post...
Back
Top Bottom