Had a key cut at Lowe's for the Seqouia and tried to use it today. Strangest thing I've seen happened. The engine would turn over but would not start, and would continue turning over until you flipped the key back to the off position. Basically you would flick it once to the start position and...
SOLD
Listing my brother in law's 1974 40. He has had it about 7 years. Good rig. Asking $8500
1969 327 - .30 over, mild cam, edelbrock aluminum intake and 650 cfm carb - about 1000 miles.
MEAN GREEN alternator
Onboard serpentine driven air compressor
Upgraded steering pump out of an FJ62...
1993 5.9 Cummins 6bt I was going to use in my swap. I DD the truck before pulling the motor, no smoke, rattles, knocks, ect. Smooth runner that ran as it should have.
149,5xx miles on the motor.
Full motor, ready to run - turbo, intercooler, full wiring harness, alt, p/s, a/c, etc.
NO...
I may be visiting Denver for a few days in August 2016 for work, and figured I may as well drive, fulfilling a dream I've had.
If I go I'd like to take my Sequoia and tour some National/State Parks, Forests, BLM's etc in the area of Denver.
I'm curious as to which trails in the area would...
SOLD
Listing this project for sale as I have run out of time to finish as well as have a career/family.
1988 FJ62 with a 1993 5.9 Cummins. Comes with new intercooler, Ford 9 inch with custom dutchman axles and wilwood discs, etc. No transmission, but most of you wouldn't have wanted the auto...
I'm parting out an entire '88 3FE motor. Motor was rebuilt by PO and oil was forgotten. Still runs, just knocks.
Let me know if you need the manifold, cam, head, etc. I'll pull parts when asked.
1992 Toyota 4 Runner. 229,931 miles, Auto, V6, PW, PDL, A/C, Cruise, CD, 4WD, Running Boards. Dark blue exterior, dark blue cloth interior. Well maintained mechanically. New head gasket, new cv joints, timing belt replaced 18,000 miles ago, transmission rebuilt less than 2000 miles ago, new...
I tried the search function and couldn't find anything about it. Googled it, and didn't really find much. Does anyone know where to look? I've got a Chrysler A518 transmission, and I'm trying to find a way to hook it up to the stock FJ62 speedometer.
I pulled the wheels off my FJ62 and found out that the lug nuts were only on by about three threads (they're aftermarket wheels)! Too risky for me.
So I'm looking for a deeper set of studs, but I've had a really hard time finding deeper ones. Does anyone know where I can find a set of longer...
I pulled the wheels off my FJ62 and found out that the lug nuts were only on by about three threads (they're aftermarket wheels)! Too risky for me.
So I'm looking for a deeper set of studs, but I've had a really hard time finding deeper ones. Does anyone know where I can find a set of...
I've been doing a TON of research looking for a set of skinnies to run on my SOA'd FJ62, but all I can find so far are bias ply. I really like the STA Super Lug's, but I've read that the bias ply's wear out incredibly fast, and at $250 a pop that doesn't seem practical.
Two questions: First...
I'm currently in the middle of doing an SOA and motor/trans swap on my 62. I'm running a dodge auto trans, and still want to run the stock FJ62 axles. The problem is that the dodge t-cases are center shaft for the rear output, and the toyota axle is of course offset.
Does anyone have a...
Looking for a mini truck axle (pre 86 I believe) so I can have my '88 FJ62 axle centered.
I'm in Gainesville, FL (32608) and can drive an hour or two to pick it up or meet.
Please let me know if you've got one or know someone who does.
Thanks!
I'm trying to decide what tires to run on my SOA'd FJ62, and want some advice from you guys that know tires better than me.
The truck will be a DD, doing very little off-roading. I'm looking for a skinnier tire, so it won't wander as much and so it'll have a little less rolling resistance...